B2430 LED Headlight LH Circuit Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- B2431 LED Headlight RH Circuit Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The illumination of the low beam headlights is controlled by the main body ECU. When the headlights are turned on, the main body ECU receives a signal from the headlight assembly and detects the illumination condition of the low beam headlights.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2430 |
LED headlight LH circuit malfunction |
|
| B2431 |
LED headlight RH circuit malfunction |
|
- HINT:
- DTC B2430 and B2431 are not output if 12 seconds have not elapsed since the ignition switch was turned ON.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2430 or B2431 output does not occur.
|
|
||||
| OK | ||
| ||
| 3. INSPECT HEADLIGHT RELAY (H-LP LO) |
Remove the headlight relay from the engine room relay block assembly.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Battery voltage applied between terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY) |
Remove the headlight relay from the engine room relay block assembly.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
Headlight relay terminal 5 - Body ground
Always
11 to 14 V
Headlight relay terminal 1 - Body ground
Text in Illustration *a
Front view of wire harness connector
(to Headlight Relay [H-LP LO])
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY) |
Remove the headlight relay from the engine room relay block assembly.
Disconnect the 2F driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Headlight relay terminal 2 - 2F-40
Always
Below 1 Ω
2F-40 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
Remove the driver side junction block assembly (Click here).

Remove the main body ECU from the driver side junction block assembly (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-15 (HRLY) - 2F-40
Always
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - HEADLIGHT) |
- *1: for LH
- *2: for RH
Remove the headlight relay from the engine room relay block assembly.
Disconnect the A86*1 and A87*2 headlight connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Headlight relay terminal 3 - A86-1 (B)*1
Always
Below 1 Ω
Headlight relay terminal 3 - A87-1 (B)*2
Always
Below 1 Ω
Headlight relay terminal 3 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (HEADLIGHT - MAIN BODY ECU AND BODY GROUND) |
Disconnect the A86*1 or A87*2 headlight unit connector.
- *1: for LH
- *2: for RH
- *1: for LH
Disconnect the G64 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
A86-3 (S) - G64-21 (LLEW)
Always
Below 1 Ω
A86-2 (LO) - Body ground
Below 1 Ω
A86-3 (S) - Body ground
10 kΩ or higher
- for RH:
Tester Connection
Condition
Specified Condition
A87-3 (S) - G46-8 (RLEW)
Always
Below 1 Ω
A87-2 (LO) - Body ground
Below 1 Ω
A87-3 (S) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 9. CHECK HEADLIGHT UNIT |
Temporarily replace the headlight with a new or normally functioning one (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2430 or B2431 output does not occur.
|
|
||||
| OK | ||
| ||
