2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

B2416 Height Control Sensor Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

w/o Air Suspension System:
The DTC is stored when the headlight swivel ECU detects malfunctions in the rear height control sensor power source or rear height control sensor.
DTC Code
DTC Detection Condition
Trouble Area
B2416
  1. Malfunction in the rear height control sensor.
  2. Open or short in the rear height control sensor circuit.
  1. Rear height control sensor sub-assembly
  2. Headlight swivel ECU assembly
  3. Harness or connector
B241A
  1. Malfunction in the rear height control sensor.
  2. Open or short in the rear height control sensor circuit.
  1. Rear height control sensor sub-assembly
  2. Headlight swivel ECU assembly
  3. Harness or connector
w/ Air Suspension System:
The DTC is stored when the headlight swivel ECU detects malfunctions in the suspension control ECU.
DTC Code
DTC Detection Condition
Trouble Area
B2416
  1. Malfunction in the suspension control ECU.
  2. Open or short in the suspension control ECU circuit.
  1. Air suspension system
  2. Suspension control ECU
  3. Headlight swivel ECU assembly
  4. Harness or connector
B241A
  1. Malfunction in the suspension control ECU.
  2. Open or short in the suspension control ECU circuit.
  1. Air suspension system
  2. Suspension control ECU
  3. Headlight swivel ECU assembly
  4. Harness or connector

WIRING DIAGRAM

E183426E04
E200986E02

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2416 or B241A output does not occur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK VEHICLE EQUIPMENT
  1. Check the vehicle equipment.

    Result 
    Result
    Proceed to
    w/o Air Suspension System
    A
    w/ Air Suspension System
    B



B
Go to step 6
A


3. READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)
  1. Using the intelligent tester, read the Data List (Click here).

    AFS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Sens Pw Supply Val
    Height control sensor power supply value / 0 to 6.25 V
    Approximately 5 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value / 0 to 5 V
    0.5 to 4.5 V
    The value changes according to the vehicle height.

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 4
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
  1. Disconnect the A58 headlight swivel ECU connector.

  1. Disconnect the S3 rear height control sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A58-18 (SBF) - S3-1 (SHB)
    Always
    Below 1 Ω
    A58-19 (SHRL) - S3-2 (SHRR)
    Always
    Below 1 Ω
    A58-21 (SGF) - S3-3 (SHG)
    Always
    Below 1 Ω
    A58-18 (SBF) - Body ground
    Always
    10 kΩ or higher
    A58-19 (SHRL) - Body ground
    Always
    10 kΩ or higher
    A58-21 (SGF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

  1. Remove the rear height control sensor (Click here).C214173E04

    Text in Illustration 
    *a
    Min. Low
    *b
    Normal
    *c
    Max. High
    -
    -
    V100135
    45°
    V100136
    45°

  1. Connect 3 dry cell batteries (1.5 V) in series.

  1. Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 3 (SHG).

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (SHG) - 2 (SHRR)
    Max. high (45°)
    4.4 to 4.6 V
    Normal (0°)
    2.3 to 2.6 V
    Min. low (-45°)
    0.4 to 0.6 V

    NOTICE:
    Do not apply a voltage of 5 V or higher.



NG
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (Click here)
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

6. CHECK FOR DTC (AIR SUSPENSION SYSTEM)
  1. Check for DTCs (Click here).

    OK:
    DTC "C1712 Front Height Control Sensor LH Circuit Malfunction" and "C1714 Rear Height Control Sensor LH Circuit Malfunction" are not output.



NG
GO TO AIR SUSPENSION SYSTEM (Click here)
OK


7. READ VALUE USING INTELLIGENT TESTER (AFS)
  1. Using the intelligent tester, read the Data List (Click here).

    AFS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Sens Pw Supply Val
    Height control sensor power supply value / 0 to 6.25 V
    Approximately 5 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value / 0 to 5 V
    0.5 to 4.5 V
    The value changes according to the vehicle height.

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 8
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

8. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - SUSPENSION CONTROL ECU)
  1. Disconnect the A58 headlight swivel ECU connector.

  1. Disconnect the A14 and R19 suspension control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A58-18 (SBF) - A14-22 (SBL)
    Always
    Below 1 Ω
    A58-19 (SHRL) - R19-27 (SHR2)
    Always
    Below 1 Ω
    A58-21 (SGF) - A14-21 (SGL)
    Always
    Below 1 Ω
    A58-18 (SBF) - Body ground
    Always
    10 kΩ or higher
    A58-19 (SHRL) - Body ground
    Always
    10 kΩ or higher
    A58-21 (SGF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK SUSPENSION CONTROL ECU (OPERATION)
  1. Temporarily replace the suspension control ECU with a new or normally functioning one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2416 or B241A output does not occur.



NG
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)
OK

END (REPLACE SUSPENSION CONTROL ECU) (Click here)


← B2415 Vehicle Speed Sensor Malfunction (from Aug 2014)B2416 Height Control Sensor Malfunction (+ B241A) (from Aug 2014) →