2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

WIRING DIAGRAM

E278320E09

INSPECTION PROCEDURE


1. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Check the radio automatic station search function by activating it.

    OK:
    Automatic station search function stops on a station.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    OK:
    Optional components are installed.

    NOTICE:
    Do not remove optional components without permission of the customer.



NG
Go to step 3
OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E276819
    Remove the antenna connector from the radio and display receiver assembly.

  1. Turn the engine switch on (ACC) with the radio and display receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

    OK:
    Noise occurs.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4. INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
  1. Inspect the quarter window assembly (window glass antenna wire) (Click here).



NG
REPAIR QUARTER WINDOW ASSEMBLY (Click here)
OK


5. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Disconnect the RA radio and display receiver assembly connector.

  1. E277921E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (ANT+) - Body ground
    Engine switch on (ACC)
    Radio switch on
    11 to 14 V



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


6. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

  1. E283632E04
    Disconnect the antenna connector from the radio and display receiver assembly.

  1. Disconnect the antenna connector from the holder antenna assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    RA-3 (RMAIN2) - 3
    Always
    Below 1 Ω
    RA-5 (ANT+) - 1
    Always
    Below 1 Ω
    RA-3 (RMAIN2) - Body ground
    Always
    10 kΩ or higher
    RA-5 (ANT+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to Holder Antenna Assembly)



NG
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


7. CHECK HOLDER ANTENNA ASSEMBLY
  1. Replace the holder antenna assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (HOLDER ANTENNA ASSEMBLY IS DEFECTIVE)


← Radio Broadcast cannot be Received or Poor Reception (Aug 2013 – Jul 2014)Illumination for Panel Switch does not Come on with Tail Switch ON (Aug 2013 – Jul 2014) →