2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A245857E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


5. REMOVE FRONT WHEEL LH

6. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 5 clips and front fender apron seal LH.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

8. DISCONNECT NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A239587E01
    Remove the 2 nuts.
    Text in Illustration 
    *1
    No. 1 Engine Cover Hook
    *2
    No. 3 Engine Cover Bracket

  1. Detach the 2 No. 1 engine cover hooks from the No. 3 engine cover bracket and remove the No. 1 engine cover.


9. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


10. DISCONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

  1. A239589
    Remove the bolt and disconnect the No. 4 vacuum transmitting pipe.


11. DISCONNECT INTERCOOLER AIR HOSE

  1. A239590
    Loosen the hose clamp and disconnect the intercooler air hose.


12. REMOVE NO. 1 INTAKE PIPE

  1. A239592
    Disconnect the 2 connectors from the intake air temperature sensor and throttle position sensor.

  1. Detach the 2 wire harness clamps.

  1. A239593
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. Remove the 2 bolts and No. 1 intake pipe.


13. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. A239594
    Disconnect the throttle control motor connector.

  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.


14. REMOVE INJECTOR DRIVER

  1. A239612
    Disconnect the 4 connectors.

  1. Remove the 2 bolts and injector driver assembly.


15. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A239651
    Remove the 3 bolts and disconnect the vane pump oil reservoir.


16. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

  1. A244615
    Disconnect the 3 vacuum switching valve connectors.

  1. A244965
    Disconnect the No. 1 vacuum transmitting hose.

  1. A244967
    Disconnect the 2 No. 2 vacuum transmitting hoses from the No. 2 EGR valve.

  1. A244966
    Disconnect the No. 1 vacuum transmitting hose and No. 4 vacuum transmitting hose.

  1. A244968
    Remove the 2 bolts and manifold stay with vacuum switching valve.


17. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A245462
    Remove the bolt and No. 2 injection pipe clamp.

  1. A239672E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side


18. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A244613
    Remove the 2 nuts and No. 3 injection pipe clamp.

  1. A244612
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A239673E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side


19. DISCONNECT HEATER WATER PIPE SUB-ASSEMBLY

  1. A239652
    Detach the water by-pass hose clamp.

  1. Remove the bolt and disconnect the heater water pipe.


20. DISCONNECT WATER BY-PASS HOSE
  1. Detach the 4 water by-pass hose clamps.

  1. Disconnect the No. 7 water by-pass hose labeled A in the illustration.

  1. Disconnect the No. 4 water by-pass hose labeled B in the illustration.

  1. Disconnect the No. 3 water by-pass hose labeled C in the illustration.

  1. Disconnect the No. 8 water by-pass hose labeled D in the illustration.

  1. Disconnect the No. 6 water by-pass hose labeled E in the illustration.

  1. Disconnect the No. 5 water by-pass hose labeled F in the illustration.

    A239653E01


21. REMOVE NO. 1 VACUUM TRANSMITTING PIPE

  1. A244611
    Disconnect the vacuum hose from the intake manifold.

  1. Remove the bolt and No. 1 vacuum transmitting pipe.


22. REMOVE WIRING HARNESS CLAMP BRACKET
  1. Disconnect the glow plug connector.

  1. A245469
    Detach the 2 wire harness clamps and disconnect the glow plug connector from the wiring harness clamp bracket.

  1. A245466
    Remove the bolt and wiring harness clamp bracket.


23. REMOVE NO. 3 ENGINE COVER BRACKET

  1. A239350
    Remove the 2 nuts and No. 3 engine cover bracket.


24. REMOVE ENGINE COVER BRACKET INSULATOR

  1. A239397
    Remove the 2 nuts and 2 engine cover bracket insulators.


25. REMOVE NO. 4 ENGINE COVER BRACKET

  1. A239426
    Remove the bolt and No. 4 engine cover bracket.


26. REMOVE AIR CONNECTOR STAY

  1. A245685
    Disconnect the 4 injector connectors and detach the 3 wire harness clamps.

  1. A239654E01
    Remove the bolt labeled A and disconnect the No. 1 fuel pipe from the air connector stay.
    Text in Illustration 
    *1
    No. 1 Fuel Pipe

  1. Remove the 3 bolts and air connector stay.


27. REMOVE EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY

  1. A239655
    Disconnect the fuel pressure sensor connector from the common rail.

  1. Remove the 4 nuts, 3 bolts and EGR cooler with No. 2 EGR valve.

  1. Remove the 2 gaskets from the cylinder head and electric EGR control valve.

    A239656E01

    Text in Illustration 
    *1
    Gasket
    -
    -


28. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Disconnect the electric EGR control valve connector.

  1. A245484E01
    Remove the electric EGR control valve and gasket from the intake air connector.
    Text in Illustration 
    *1
    Intake Air Connector


29. DISCONNECT WIRE HARNESS

  1. A245686
    Remove the bolt and disconnect the wire harness.

  1. A246260
    for LHD:
    Remove the bolt and disconnect the wire harness.

  1. Detach the 5 clamps and disconnect the wire harness from the cowl top panel.


30. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

  1. A239598
    Disconnect the manifold absolute pressure sensor connector and vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.


31. REMOVE EMISSION CONTROL VALVE BRACKET

  1. A239639
    Remove the bolt and emission control valve bracket.


32. REMOVE THROTTLE BODY BRACKET

  1. A244614
    Remove the 3 bolts and throttle body bracket.


33. REMOVE NO. 1 GAS FILTER

  1. A244608
    Disconnect the vacuum hose and remove the No. 1 gas filter from the gas filter bracket.


34. REMOVE GAS FILTER BRACKET

  1. A246247
    Detach the clamp and disconnect the wire harness.

  1. A244609
    Remove the bolt and gas filter bracket.


35. REMOVE INTAKE AIR CONNECTOR

  1. A245684
    Remove the 3 bolts, intake air connector and gasket.


36. REMOVE NO. 1 FUEL PIPE
  1. Disconnect the No. 2 fuel pipe (Click here).

  1. Remove the 4 bolts, union bolt, gasket and No. 1 fuel pipe.

    A239663E01

    Text in Illustration 
    *1
    No. 2 Fuel Pipe
    -
    -
    V100136
    Union Bolt
    -
    -


37. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A239621
    Remove the bolt, nut and 2 No. 2 injection pipe clamps.

  1. A239619E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe sub-assembly.
    Text in Illustration 
    *a
    Common Rail Assembly Side
    *b
    Injector Assembly Side


38. REMOVE NO. 2 FUEL PIPE

  1. A329755
    Using a 6 mm hexagon wrench, remove the union bolt and gasket.
    Text in Illustration 
    V100135
    Union Bolt
    V100136
    Fuel Check Valve
    V100137
    Bolt

  1. Remove the fuel check valve and gasket.

  1. Remove the bolt and No. 2 fuel pipe.


39. REMOVE NO. 3 NOZZLE LEAKAGE PIPE

  1. A239624
    Disconnect the 2 fuel hoses.
    Text in Illustration 
    V100136
    Fuel Check Valve

  1. Remove the 2 bolts.

  1. Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.


40. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A329756
    Remove the 2 bolts.
    Text in Illustration 
    V100136
    Union Bolt

  1. Remove the union bolt, gasket and No. 2 nozzle leakage pipe assembly.


41. REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A244984
    Remove the 4 bolts and No. 2 cylinder head cover sub-assembly.


42. REMOVE VENTILATION PIPE

  1. A308001
    Type A
    Slide the 2 clamps and disconnect the No. 3 turbo water hose and No. 4 turbo water hose from the ventilation pipe.

  1. A308002E01
    Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe from the cylinder head sub-assembly.
    Text in Illustration 
    *A
    Type A
    *B
    Type B


43. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover sub-assembly is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying the portion between the nozzle holder seal and the cutout part of the cylinder head cover sub-assembly.

  1. A223193
    Remove the 10 bolts, 2 nuts, cylinder head cover sub-assembly and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover sub-assembly.


44. REMOVE INJECTOR ASSEMBLY

  1. A076779E04
    Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe assembly.
    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe assembly, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe assembly, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A076780E02
    Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injector assemblies.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector assembly.

  1. Remove the 4 injection nozzle seats from the cylinder head sub-assembly.


45. REMOVE NO. 1 RADIATOR HOSE

A246596

46. REMOVE FAN SHROUD

  1. A218371
    Disconnect the No. 1 water by-pass hose and detach the 2 clamps from the fan shroud.

  1. Disconnect the No. 2 water by-pass hose from the radiator reservoir.

  1. Remove the 3 bolts and radiator reservoir.

  1. for Automatic Transmission:

    1. A218382
      Remove the inlet and outlet oil cooler hoses and detach the clamp from the fan shroud.

    2. Disconnect the 2 oil cooler hoses from the radiator.

  1. A224959
    Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan and generator V belt (Click here).

  1. A218369
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts for the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Detach the No. 2 water by-pass hose from the hose clamp on the fan shroud.

  1. A224943
    Remove the No. 2 water by-pass hose from the water inlet.

  1. Remove the fan pulley from the water pump.


47. REMOVE NO. 1 TIMING BELT COVER

  1. A015094E01
    Remove the 6 bolts, 6 washers and timing belt cover.


48. REMOVE TIMING BELT

  1. A070549E05
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.

  1. A070550E01
    Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.

  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks and then turn the crankshaft clockwise to align the timing marks.


49. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.


50. REMOVE CAMSHAFT TIMING PULLEY

  1. A060182E01
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure the timing belt is not installed when removing the bolt of camshaft timing pulley.

  1. Remove the camshaft timing pulley.


51. REMOVE NO. 2 TIMING BELT COVER

  1. A225464
    Remove the 4 bolts, nut and No. 2 timing belt cover.


52. REMOVE CAMSHAFT

  1. A060148E03
    Turn the camshaft with a wrench so that the key groove of the camshaft faces upward.
    Text in Illustration 
    *1
    Key Groove

  1. A060147E01
    Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 15 bearing cap bolts, 5 bearing caps, oil seal and 2 camshafts.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →