2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Front Passenger Side Seat Belt Warning Light Malfunction

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The combination meter detects the state of the front seat inner belt RH*1 (or LH*2) when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the front seat belt warning light in the combination meter blinks. If the seat belt is fastened, the warning light goes off.
  1. *1: for LHD
  2. *2: for RHD

HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

C296992E01

INSPECTION PROCEDURE

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. READ VALUE USING INTELLIGENT TESTER
  1. Check the Data List for proper functioning of the front passenger side seat belt buckle switch (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P- Seatbelt Buckle SW
    Front passenger side seat belt buckle signal / ON or OFF
    ON: Front passenger side seat belt fastened
    OFF: Front passenger side seat belt unfastened
    -

    OK:
    The display is as specified in the normal condition column.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2. INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
C213678
  1. Remove the front seat assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    More than 147 N (15 kgf, 33.0 lbf) applied to occupant detection sensor
    Below 100 Ω



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR) (Click here)
OK


3. INSPECT FRONT SEAT INNER BELT ASSEMBLY

  1. C213676E03
    Remove the front seat inner belt assembly RH*1 or LH*2 (Click here).
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (E) - 3
    Always
    Below 1 Ω
    3 (+) - 1
    Front passenger side seat belt unfastened
    3 (+) - 1
    Front passenger side seat belt fastened
    10 kΩ or higher



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT PASSENGER SIDE INNER BELT AND BODY GROUND)
  1. Disconnect the G7 meter connector.

  1. Disconnect the Q21*1 or R34*2 inner belt connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    G7-15 (P/SB) - Q21-3 (+)
    Always
    Below 1 Ω
    Q21-2 (E) - Body ground
    G7-15 (P/SB) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    G7-15 (P/SB) - R34-3 (+)
    Always
    Below 1 Ω
    R34-2 (E) - Body ground
    G7-15 (P/SB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Driver Side Seat Belt Warning Light does not Operate (from Aug 2014)Front Passenger Side Seat Belt Warning Light Malfunction (from Aug 2014) →