VC Output Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
|
|
||||
| B | |
| 2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and tester on.
Check the communication between the tester and ECM.
Result Result
Proceed to
Communication is possible
A
Communication is not possible
B
|
|
||||
| B | |
| 3. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| B | |
| 4. CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the throttle position sensor connector.
|
|
||||
| B | |
| 5. CHECK MIL (FUEL PRESSURE SENSOR) |
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the fuel pressure sensor connector.
|
|
||||
| B | |
| 6. CHECK MIL (EGR VALVE POSITION SENSOR) |
Disconnect the EGR valve position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the EGR valve position sensor connector.
|
|
||||
| B | |
| 7. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the manifold absolute pressure sensor connector.
|
|
||||
| B | |
| 8. CHECK MIL (NOZZLE VANE POSITION SENSOR) |
Disconnect the nozzle vane position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the nozzle vane position sensor connector.
|
|
||||
| B | |
| 9. CHECK HARNESS AND CONNECTOR |
Disconnect the accelerator pedal position sensor connector.
Disconnect the throttle position sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the EGR position sensor connector.
Disconnect the nozzle vane position sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G58-6 (VCPA) - Body ground
Always
10 kΩ or higher
G58-4 (VCP2) - Body ground
Always
10 kΩ or higher
C91-8 (VCVL) - Body ground
Always
10 kΩ or higher
C90-14 (VCM) - Body ground
Always
10 kΩ or higher
C90-13 (VCS) - Body ground
Always
10 kΩ or higher
C91-13 (VCEG) - Body ground
Always
10 kΩ or higher
C91-12 (VCPM) - Body ground
Always
10 kΩ or higher
C91-11 (VNVC) - Body ground
Always
10 kΩ or higher
Reconnect the accelerator pedal position sensor connector.
Reconnect the throttle position sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the EGR position sensor connector.
Reconnect the nozzle vane position sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the ECM connectors.
|
|
||||
| OK | ||
| ||
