2013-2015 Land Cruiser Prado · Service Manual Brake

C0278 Open in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The solenoid relay is built into the master cylinder solenoid.
This relay supplies power to each solenoid. If the initial check is OK, after the ignition switch is turned to ON, the relay turns on.
DTC Code
DTC Detection Condition
Trouble Area
C0278
Either condition is met:
  1. Both of the following conditions continue for at least 0.2 seconds.
    1. IG voltage is between 9.5 and 17 V.
    2. The relay contact is open when the relay is on.
  2. Both of the following conditions continue for at least 0.2 seconds.
    1. IG voltage is 9.5 V or less when the relay is on.
    2. The relay contact remains open.
  1. ABS NO. 2 fuse
  2. Solenoid relay circuit
  3. Master cylinder solenoid
C0279
The following condition continues for at least 0.2 seconds.
  1. The relay contact is closed immediately after turning the ignition switch to ON when the relay is off.

WIRING DIAGRAM

Refer to DTCs C0226, C0236, C0246, C0256, C1225, C1226, C1227 and C1228 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK TERMINAL VOLTAGE (+BS)
  1. Disconnect the A7 skid control ECU connector.

  1. C214161E27
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-31 (+BS) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (GND1, GND2, AND GND3 TERMINAL)
  1. Disconnect the A7 and A8 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A7-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A8-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. RECONFIRM DTC

HINT:
These codes are stored when a problem is detected in the master cylinder solenoid.
The solenoid relay is in the master cylinder solenoid.
Therefore, solenoid relay circuit inspections and relay unit inspections cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C0226 SFR Solenoid Circuit (+ 7 more codes) (from Aug 2014)C0278 Open in ABS Solenoid Relay Circuit (+ C0279) (from Aug 2014) →