2013-2015 Land Cruiser Prado · Service Manual Brake

C1380 Stop Light Control Relay Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU (master cylinder solenoid), the stop light control ECU contact turns on and the stop light comes on.
DTC Code
DTC Detection Condition
Trouble Area
C1380
Either condition is met:
  1. When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control ECU assembly drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.
  2. When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control ECU assembly drive output (STPO) is off, the signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.
  1. STOP fuse
  2. Stop light switch circuit
  3. Stop light control ECU assembly
  4. Stop light control ECU circuit
  5. Skid control ECU (Master cylinder solenoid)

WIRING DIAGRAM

C294401E04

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    On
    Brake pedal released
    Off



NG
Go to step 6
OK


2. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 9
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control ECU
    ECU ON/OFF
    Observe the stop lights (do not come on for 2 to 5 seconds).

  1. While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Relay Output
    Stop light control ECU output/ ON or OFF
    ON: Stop light control ECU on (Stop lights on)
    OFF: Stop light control ECU off (Stop lights off)
    -

Result 
Result
Proceed to
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off
A
When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on
B


B
Go to step 10
A


4. CHECK TERMINAL VOLTAGE (STP2)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. C214161E30
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-45 (STP2) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Master Cylinder Solenoid])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

6. CHECK TERMINAL VOLTAGE AND RESISTANCE (+B, GND)
  1. Disconnect the A54 stop light control ECU assembly connector.

  1. C207207E04
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A54-6 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A54-8 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control ECU Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK TERMINAL VOLTAGE (STP)
  1. Disconnect the A54 stop light control ECU assembly connector.

  1. C207207E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A54-5 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Control ECU Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL ECU ASSEMBLY - MASTER CYLINDER SOLENOID)
  1. Disconnect the A54 stop light control ECU assembly connector.

  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A54-1 (OUT) - A7-45 (STP2)
    Always
    Below 1 Ω
    A54-1 (OUT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STOP LIGHT CONTROL ECU ASSEMBLY (Click here)

9. CHECK TERMINAL VOLTAGE (STP)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. C214161E31
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Master Cylinder Solenoid])
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

10. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT CONTROL ECU ASSEMBLY)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the A54 stop light control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-16 (STP0) - A54-9 (ACC)
    Always
    Below 1 Ω
    A7-16 (STP0) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT CONTROL ECU ASSEMBLY)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the A54 stop light control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-45 (STP2) - A54-1 (OUT)
    Always
    Below 1 Ω
    A7-45 (STP2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STOP LIGHT CONTROL ECU ASSEMBLY (Click here)


← C1380 Stop Light Control Relay Malfunction (Aug 2013 – Jul 2014)C1381 Acceleration Sensor Power Supply Voltage Malfunction (Aug 2013 – Jul 2014) →