2013-2015 Land Cruiser Prado · Service Manual Suspension

C1782/82 Low Battery Positive Voltage

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
C1782/82
The voltage at terminal IG or B is 10 V or less or 16 V or higher for 0.5 seconds.
  1. Battery
  2. Charging system
  3. AIR SUS fuse
  4. AIR SUS NO. 2 fuse
  5. AVS fuse
  6. Harness or connector
  7. Suspension control ECU

WIRING DIAGRAM

C218589E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the suspension control ECU, perform registration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. READ VALUE USING INTELLIGENT TESTER (IG/+B POWER SOURCE VOLTAGE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG Power Source Voltage
    Actual ECU power supply voltage / Min.: 0.0 V, Max.: 25.5 V
    Ignition switch ON: 11 to 14 V
    -
    +B Power Source Voltage
    Actual battery supply voltage / Min.: 0.0 V, Max.: 25.5 V
    Ignition switch ON: 11 to 14 V
    -

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to problem symptoms table)
    B
    OK (When troubleshooting according to DTC chart)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK TERMINAL VOLTAGE (IG, B)
  1. Disconnect the A49 suspension control ECU connector.

  1. C216018E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-3 (B) - Body ground
    Always
    11 to 14 V
    A49-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Suspension Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BODY GROUND)
  1. Disconnect the A49 and R19 suspension control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R19-10 (GND) - Body ground
    Always
    Below 1Ω
    A49-5 (GND) - Body ground
    Always
    Below 1Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE SUSPENSION CONTROL ECU (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1781/81 Suspension Control ECU Malfunction (from Aug 2014)C1782/82 Low Battery Positive Voltage (from Aug 2014) →