2013-2015 Land Cruiser Prado · Service Manual Suspension

C1751/51 Compressor Relay Coil Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the "up" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to the AIR SUS relay to turn the relay on.
As a result, the current flows to the AIR SUS relay coil, closing the relay contact, and then battery positive voltage is applied to the height control compressor, which causes compressed air to raise the vehicle height.
DTC Code
DTC Detection Condition
Trouble Area
C1751/51
Either condition is met:
  1. With the AIR SUS relay inactivated, an open signal of the AIR SUS relay is detected for 1 second or more.
  2. With the AIR SUS relay activated, a short signal of the AIR SUS relay is detected 8 times successively.
  1. Harness or connector
  2. AIR SUS relay (Suspension control relay)
  3. Suspension control ECU

HINT:
Once the suspension control ECU stores DTC C1751/51 in memory, vehicle height control is suspended until a normal signal is input to the suspension control ECU from the AIR SUS relay. However, control is resumed if the ignition switch is turned off and then to ON again.


WIRING DIAGRAM

C218583E01

INSPECTION PROCEDURE

NOTICE:
When replacing the suspension control ECU, perform registration (Click here).

HINT:
If DTC C1782/82 is output at the same time as C1751/51, perform the inspection necessary for DTC C1782/82 first (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COMPRESSOR MOTOR RELAY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Compressor Motor Relay
    AIR SUS relay
    ON or OFF
    1. The operating sound of the motor can be heard.
    2. When the Active Test is performed, Motor Relay in the Data List changes between ON and OFF accordingly.

    OK:
    Operation of motor can be heard.

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to problem symptoms table)
    B
    OK (When troubleshooting according to DTC chart)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2. INSPECT SUSPENSION CONTROL RELAY (AIR SUS)
  1. Turn the ignition switch off.

  1. Remove the AIR SUS relay from the engine room relay block.

  1. C149624E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    12 V battery voltage is not applied to terminal 1 and 2
    10 kΩ or higher
    12 V battery voltage is applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    AIR SUS Relay



NG
REPLACE SUSPENSION CONTROL RELAY (AIR SUS)
OK


3. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - AIR SUS RELAY)
  1. Disconnect the R19 suspension control ECU connector.

  1. Remove the AIR SUS relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R19-22 (RC) - Engine room relay block AIR SUS relay terminal 1
    Always
    Below 1 Ω
    R19-22 (RC) - Body ground
    Always
    10 kΩ or higher
    Engine room relay block AIR SUS relay terminal 2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1751/51 Compressor Relay Coil Malfunction (Aug 2013 – Jul 2014)C1752/52 Compressor Motor Malfunction (Aug 2013 – Jul 2014) →