Unable to Lock Steering Wheel
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The steering lock ECU sends an unlock position signal to the power management control ECU. Upon receiving the signal, the power management control ECU permits an engine start. This prevents the engine from being started with the steering locked.The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering wheel.
When the steering lock is operating, the steering lock may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering lock can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.
The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:
- With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.
- NOTICE:
- If the steering lock actuator assembly (steering lock ECU) is replaced, with the engine switch off and the shift lever in P (for Automatic Transmission), open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.
- When replacing the steering lock ECU, ID code box or certification ECU, registration must be performed. Refer to the Service Bulletin for the registration procedure.
- If the steering lock actuator assembly (steering lock ECU) is replaced, with the engine switch off and the shift lever in P (for Automatic Transmission), open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.
| 1. READ VALUE USING INTELLIGENT TESTER (LOCK REQUEST RECEIVE) |
Use the Data List to check if the steering lock command is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Lock Request Receive
Steering lock lock command reception status/NG or OK
NG: Lock request not received
OK: Lock request received
-
- OK:
- The certification ECU receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door, and OK is displayed on the intelligent tester screen.
|
|
||||
| OK | |
| 2. INSPECT STEERING LOCK ECU |
Move the shift lever to P.*
- *: for Automatic Transmission
- *: for Automatic Transmission
Measure the resistance and voltage according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G35-1 (GND) - Body ground
Always
Below 1 Ω
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G35-3 (IGE) - G35-1 (GND)
Steering lock motor operating immediately after turning engine switch from off to on (IG)
Below 1 V
G35-3 (IGE) - G35-1 (GND)
Steering lock motor not operating
11 to 14 V
Text in Illustration *a
Component with harness connected
(Steering Lock ECU)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.
Disconnect the G35 steering lock ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G35-3 (IGE) - G51-8 (SLR+)
Always
Below 1 Ω
G35-3 (IGE) or G51-8 (SLR+) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
NG
A
OK
for Manual Tilt and Manual Telescopic Steering Column
B
for Power Tilt and Power Telescopic Steering Column
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. READ VALUE USING INTELLIGENT TESTER (FL AND FR DOOR COURTESY) |
Use the Data List to check if the driver side door courtesy switch is functioning properly.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FL Door Courtesy
Front door courtesy switch LH/ON or OFF
ON: Front door courtesy switch LH on
OFF: Front door courtesy switch LH off
-
FR Door Courtesy
Front door courtesy switch RH/ON or OFF
ON: Front door courtesy switch RH on
OFF: Front door courtesy switch RH off
-
- OK:
- Driver side door courtesy switch is functioning properly.
|
|
||||
| OK | |
| 5. READ VALUE USING INTELLIGENT TESTER (S CODE CHECK) |
Use the Data List to check if the S code certification is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
S Code Check
S code certification result/NG or OK
OK: S code certification result normal
NG: S code certification result abnormal
-
- OK:
- OK is displayed on the intelligent tester.
|
|
||||
| OK | |
| 6. READ VALUE USING INTELLIGENT TESTER (L CODE CHECK) |
Use the Data List to check if the L code certification is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
L Code Check
L code certification result/NG or OK
OK: L code certification result normal
NG: L code certification result abnormal
-
- OK:
- OK is displayed on the intelligent tester.
|
|
||||
| OK | |
| 7. REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) |
Replace the steering lock actuator assembly (steering lock ECU) (Click here for Manual Tilt and Manual Telescopic Steering Column, Click here for Power Tilt and Power Telescopic Steering Column).
| NEXT | |
| 8. CHECK STEERING LOCK RELEASE OPERATION |
Turn the engine switch on (IG).
Operate the steering wheel and check the steering lock condition.
- OK:
- Steering lock is released.
|
|
||||
| OK | ||
| ||
| 9. REPLACE ID CODE BOX |
Replace the ID code box.
| NEXT | |
| 10. READ VALUE USING INTELLIGENT TESTER (S CODE CHECK) |
Use the Data List to check if the S code certification is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
S Code Check
S code certification result/NG or OK
OK: S code certification result normal
NG: S code certification result abnormal
-
- OK:
- OK is displayed on the intelligent tester.
|
|
||||
| OK | ||
| ||
| 11. REPLACE ID CODE BOX |
Replace the ID code box.
| NEXT | |
| 12. READ VALUE USING INTELLIGENT TESTER (L CODE CHECK) |
Use the Data List to check if the L code certification is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
L Code Check
L code certification result/NG or OK
OK: L code certification result normal
NG: L code certification result abnormal
-
Result Result
Proceed to
OK is displayed on the intelligent tester.
A
NG is displayed on the intelligent tester.
for Manual Tilt and Manual Telescopic Steering Column
B
for Power Tilt and Power Telescopic Steering Column
C
|
|
||||
|
|
||||
| A | ||
| ||
