2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.
DTC Code
DTC Detection Condition
Trouble Area
B2799
One of the following conditions is met:
  1. An error in communication between the ECM and transponder key ECU assembly.
  2. An error in the communication lines.
  3. The ECU - ECM communication ID is different during communication with the transponder key ECU assembly.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM

WIRING DIAGRAM

B235863E22
B235863E21

INSPECTION PROCEDURE

NOTICE:
When replacing the transponder key ECU assembly and/or ECM, refer to the Service Bulletin.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. REREGISTER ECU - ECM COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


4. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.



NG
Go to step 6
OK

END

6. CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
  1. Disconnect the G138*1 or G74*2 ECU connector.

    1. *1: for 5L-E
    2. *2: except 5L-E

  1. Disconnect the G60*1, G56*2, G58*3 or G61*4 ECM connector.

    1. *1: for 2TR-FE
    2. *2: for 1GR-FE
    3. *3: for 1KD-FTV
    4. *4: for 5L-E

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - G60-31 (IMI)
    Always
    Below 1 Ω
    G74-12 (EFII) - G60-32 (IMO)
    G74-13 (EFIO) or G60-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    G74-12 (EFII) or G60-32 (IMO) - Body ground
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - G56-14 (IMI)
    Always
    Below 1 Ω
    G74-12 (EFII) - G56-20 (IMO)
    G74-13 (EFIO) or G56-14 (IMI) - Body ground
    Always
    10 kΩ or higher
    G74-12 (EFII) or G56-20 (IMO) - Body ground
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - G58-28 (IMI)
    Always
    Below 1 Ω
    G74-12 (EFII) - G58-29 (IMO)
    G74-13 (EFIO) or G58-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    G74-12 (EFII) or G58-29 (IMO) - Body ground
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    G138-13 (EFIO) - G61-17 (IMI)
    Always
    Below 1 Ω
    G138-12 (EFII) - G61-6 (IMO)
    G138-13 (EFIO) or G61-17 (IMI) - Body ground
    Always
    10 kΩ or higher
    G138-12 (EFII) or G61-6 (IMO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


NEXT


9. REREGISTER ECU - ECM COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


10. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


11. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2TR-FE)
    B
    NG (for 1GR-FE)
    C
    NG (for 1KD-FTV)
    D
    NG (for 5L-E)
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU IS DEFECTIVE)


← B2797 Communication Malfunction No. 1 (from Aug 2013)B2799 Engine Immobiliser System Malfunction (from Aug 2014) →