2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2797 Communication Malfunction No. 1

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

This DTC is stored when a communication error occurs between the transponder key amplifier and transponder key ECU assembly. Some possible reasons for the communication error are: 1) 2 or more ignition keys are positioned too close together, or 2) noise is occurring in the communication line.
DTC Code
DTC Detection Condition
Trouble Area
B2797
2 or more ignition keys are positioned too close to each other or noise occurs in the communication line.
  1. Key
  2. Harness or connector
  3. Transponder key amplifier
  4. Transponder key ECU assembly

WIRING DIAGRAM

B224123E15

INSPECTION PROCEDURE

NOTICE:
When replacing the transponder key ECU assembly, refer to the Service Bulletin.


1. CHECK KEY

  1. B213624
    Check whether the ignition key being used is near other ignition keys, as shown in the illustration. Also, check whether a key ring is in contact with the key grip.
    Result 
    Result
    Proceed to
    Key is near other keys and/or key ring is in contact with key grip
    A
    Key is not near other keys and key ring is not in contact with key grip
    B



B
Go to step 3
A


2. CHECK FOR DTC
  1. Separate the keys from each other or remove the key ring.

  1. Clear the DTCs (Click here).

  1. Insert a key into the ignition key cylinder, and then remove it. Repeat this for all the other keys.

  1. Check that no DTC is output (Click here).

    OK:
    DTC B2797 is not output.



NG
Go to step 3
OK

END

3. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
  1. Disconnect the G138*1 or G74*2 ECU connector.

    1. *1: for 5L-E
    2. *2: except 5L-E

  1. Disconnect the G75 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    G138-15 (CODE) - G75-4 (CODE)
    Always
    Below 1 Ω
    G138-15 (CODE) or G75-4 (CODE) - Body ground
    Always
    10 kΩ or higher
    except 5L-E 
    Tester Connection
    Condition
    Specified Condition
    G74-15 (CODE) - G75-4 (CODE)
    Always
    Below 1 Ω
    G74-15 (CODE) or G75-4 (CODE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK TRANSPONDER KEY ECU ASSEMBLY (NOISE)
  1. *1: for 5L-E
  2. *2: except 5L-E

  1. B237349E03
    Using an oscilloscope, check for noise in the waveform between the terminals of the G75 amplifier connector and G138*1 or G74*2 ECU connector.
    Measurement Condition 
    Item
    Content
    Tester Connection
    G75-4 (CODE) - G138-15 (CODE)*1
    G75-4 (CODE) - G74-15 (CODE)*2
    Tool Setting
    5 V/DIV., 20 ms./DIV.
    Condition
    Key inserted in ignition key cylinder

    OK:
    No noise is present.

    Text in Illustration 
    *A
    for 5L-E
    *B
    except 5L-E
    *a
    Component with harness connected
    (Transponder Key Amplifier)
    *b
    Component with harness connected
    (Transponder Key ECU Assembly)
    *c
    Noise should not appear



NG
FIND CAUSE OF NOISE AND REMOVE IT
OK


5. REPLACE TRANSPONDER KEY AMPLIFIER
  1. Temporarily replace the transponder key amplifier with a new or normally functioning one (Click here).


NEXT


6. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts normally.

    OK:
    Engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)


← B2796 No Communication in Immobiliser System (+ B2798) (from Aug 2013)B2799 Engine Immobiliser System Malfunction (Aug 2013 – Jul 2014) →