B2799 Engine Immobiliser System Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2799 |
One of the following conditions is met:
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- When replacing the transponder key ECU assembly and/or ECM, refer to the Service Bulletin.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
| 3. REREGISTER ECU - ECM COMMUNICATION ID |
Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 4. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
| 6. CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Check that the connectors are properly connected to the ECM and transponder key ECU assembly.
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM) |
Disconnect the G138*1 or G74*2 ECU connector.
- *1: for 5L-E
- *2: except 5L-E
- *1: for 5L-E
Disconnect the G60*1, G56*2, G58*3 or G61*4 ECM connector.
- *1: for 2TR-FE
- *2: for 1GR-FE
- *3: for 1KD-FTV
- *4: for 5L-E
- *1: for 2TR-FE
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 2TR-FE Tester Connection
Condition
Specified Condition
G74-13 (EFIO) - G60-31 (IMI)
Always
Below 1 Ω
G74-12 (EFII) - G60-32 (IMO)
G74-13 (EFIO) or G60-31 (IMI) - Body ground
Always
10 kΩ or higher
G74-12 (EFII) or G60-32 (IMO) - Body ground
for 1GR-FE Tester Connection
Condition
Specified Condition
G74-13 (EFIO) - G56-14 (IMI)
Always
Below 1 Ω
G74-12 (EFII) - G56-20 (IMO)
G74-13 (EFIO) or G56-14 (IMI) - Body ground
Always
10 kΩ or higher
G74-12 (EFII) or G56-20 (IMO) - Body ground
for 1KD-FTV Tester Connection
Condition
Specified Condition
G74-13 (EFIO) - G58-28 (IMI)
Always
Below 1 Ω
G74-12 (EFII) - G58-29 (IMO)
G74-13 (EFIO) or G58-28 (IMI) - Body ground
Always
10 kΩ or higher
G74-12 (EFII) or G58-29 (IMO) - Body ground
for 5L-E Tester Connection
Condition
Specified Condition
G138-13 (EFIO) - G61-17 (IMI)
Always
Below 1 Ω
G138-12 (EFII) - G61-6 (IMO)
G138-13 (EFIO) or G61-17 (IMI) - Body ground
Always
10 kΩ or higher
G138-12 (EFII) or G61-6 (IMO) - Body ground
|
|
||||
| OK | |
| 8. REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).
| NEXT | |
| 9. REREGISTER ECU - ECM COMMUNICATION ID |
Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 10. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 11. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
Result Result
Proceed to
OK
A
NG (for 2TR-FE)
B
NG (for 1GR-FE)
C
NG (for 1KD-FTV)
D
NG (for 5L-E)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
