2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Reverse Signal Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The clearance warning ECU receives a reverse shift position signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

E280619E08
E280619E09

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK CLEARANCE WARNING ECU

  1. B144569E08
    Disconnect the clearance warning ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 4 Sensor Type 
    Tester Connection
    Condition
    Specified Condition
    I1-8 (RL) - Body ground
    Engine switch on (IG)
    Shift lever in R
    11 to 14 V
    I1-8 (RL) - Body ground
    Engine switch on (IG)
    Shift lever in any position except R
    Below 1 V
    for 8 Sensor Type 
    Tester Connection
    Condition
    Specified Condition
    G154-8 (RL) - Body ground
    Engine switch on (IG)
    Shift lever in R
    11 to 14 V
    G154-8 (RL) - Body ground
    Engine switch on (IG)
    Shift lever in any position except R
    Below 1 V

    Text in Illustration 
    *A
    for 4 Sensor Type
    *B
    for 8 Sensor Type
    *a
    Front view of wire harness connector
    (to Clearance Warning ECU)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Automatic Transmission)
    B
    NG (for Manual Transmission)
    C



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Remove the park/neutral position switch assembly.

    1. for A343F: Click here
    2. for A750F: Click here

  1. Inspect the park/neutral position switch assembly.

    1. for A343F: Click here
    2. for A750F: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for A343F)
    B
    NG (for A750F)
    C



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
A


3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU AND BATTERY)
  1. Disconnect the C40 park/neutral position switch assembly connector.

  1. Disconnect the I1*1 or G154*2 clearance warning ECU connector.

    1. *1: for 4 Sensor Type
    2. *2: for 8 Sensor Type

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C40-2 (RB) - Body ground
    Engine switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 4 Sensor Type 
    Tester Connection
    Condition
    Specified Condition
    I1-8 (RL) - C40-1 (RL)
    Always
    Below 1 Ω
    I1-8 (RL) - Body ground
    Always
    10 kΩ or higher
    for 8 Sensor Type 
    Tester Connection
    Condition
    Specified Condition
    G154-8 (RL) - C40-1 (RL)
    Always
    Below 1 Ω
    G154-8 (RL) - Body ground
    Always
    10 kΩ or higher

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE CLEARANCE WARNING ECU (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE CLEARANCE WARNING ECU (Click here)

4. INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
  1. Remove the back-up light switch assembly.

    1. for R150F: Click here
    2. for RA61F: Click here
    3. for G52F: Click here

  1. Inspect the back-up light switch assembly.

    1. for R150F: Click here
    2. for RA61F: Click here
    3. for G52F: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for R150F)
    B
    NG (for RA61F)
    C
    NG (for G52F)
    D



B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

C
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

D
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)
A


5. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU AND BATTERY)
  1. Disconnect the C41 back-up light switch assembly connector.

  1. Disconnect the I1*1 or G154*2 clearance warning ECU connector.

    1. *1: for 4 Sensor Type
    2. *2: for 8 Sensor Type

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C41-2 - Body ground
    Engine switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 4 Sensor Type 
    Tester Connection
    Condition
    Specified Condition
    I1-8 (RL) - C41-1
    Always
    Below 1 Ω
    I1-8 (RL) - Body ground
    Always
    10 kΩ or higher
    for 8 Sensor Type 
    Tester Connection
    Condition
    Specified Condition
    G154-8 (RL) - C41-1
    Always
    Below 1 Ω
    G154-8 (RL) - Body ground
    Always
    10 kΩ or higher

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE CLEARANCE WARNING ECU (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE CLEARANCE WARNING ECU (Click here)


← Reverse Signal Circuit (Aug 2013 – Jul 2014)Main Switch Circuit (Aug 2013 – Jul 2014) →