2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Main Switch Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

for 4 Sensor Type:
When the back sonar or clearance sonar switch assembly is turned on, the on signal is input into the ECU.
for 8 Sensor Type
When the driving support switch control ECU receives the clearance sonar on/off switch signal, the ECU sends it to the clearance warning ECU.

WIRING DIAGRAM

E285868E01
E283772E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Clearance Sonar / Data List.

  1. According to the display on the GTS, read the Data List.

    Clearance Sonar 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    TOYOTA parking assist-sensor system (multi-function switch)/OFF or ON
    OFF: TOYOTA parking assist-sensor system off
    ON: TOYOTA parking assist-sensor system on
    -

    OK:
    The display changes as shown above when the TOYOTA parking assist-sensor system is operated.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 4 Sensor Type)
    B
    NG (for 8 Sensor Type)
    C



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
  1. Remove the back sonar or clearance sonar switch assembly (Click here).

  1. Inspect the back sonar or clearance sonar switch assembly (Click here).



NG
REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU, BATTERY AND BODY GROUND)
  1. Disconnect the G13 back sonar or clearance sonar switch assembly connector.

  1. Disconnect the I1 clearance warning ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G13-6 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G13-3 (ECU) - I1-12 (CSSW)
    Always
    Below 1 Ω
    G13-7 (IND) - Body ground
    Always
    Below 1 Ω
    G13-3 (ECU) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE CLEARANCE WARNING ECU (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE CLEARANCE WARNING ECU (Click here)

4. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - CLEARANCE WARNING ECU)
  1. Disconnect the G162*1 or G76*2 driving support switch control ECU connector.

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

  1. Disconnect the G154 clearance warning ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Automatic Transmission 
    Tester Connection
    Condition
    Specified Condition
    G162-9 (SWO1) - G154-12 (CSSW)
    Always
    Below 1 Ω
    G162-9 (SWO1) - Body ground
    Always
    10 kΩ or higher
    for Manual Transmission 
    Tester Connection
    Condition
    Specified Condition
    G76-12 (SWO1) - G154-12 (CSSW)
    Always
    Below 1 Ω
    G76-12 (SWO1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK DRIVING SUPPORT SWITCH CONTROL ECU
  1. Replace the driving support switch control ECU with a new or normally functioning one (Click here).

  1. Check the TOYOTA parking assist-sensor system operates normally.

    OK:
    TOYOTA parking assist-sensor system operates normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE CLEARANCE WARNING ECU (Click here)

C
REPLACE CLEARANCE WARNING ECU (Click here)
A

END (DRIVING SUPPORT SWITCH CONTROL ECU IS DEFECTIVE)


← Reverse Signal Circuit (from Aug 2014)Main Switch Circuit (from Aug 2014) →