2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Reclining Motor Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The fold seat control ECU receives switch operation signals from the No. 1 and No. 2 fold seat switches and rear power seat switch and activates the power seat motors. At this time, the Hall IC detects the actuation of the seatback and sends a seatback actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM

B239515E02

INSPECTION PROCEDURE


1. INSPECT NO. 3 SEATBACK FRAME SUB-ASSEMBLY (RECLINING MOTOR)

  1. B239766E01
    for LH Side:
    1. Remove the No. 3 seatback frame sub-assembly LH (Click here).

    2. Check if the No. 3 seatback frame moves smoothly when the battery is connected to the reclining motor connector terminals.

  1. for RH Side:

    1. Remove the No. 3 seatback frame sub-assembly RH (Click here).

    2. Check if the No. 3 seatback frame moves smoothly when the battery is connected to the reclining motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 3 (FWD)
      Battery negative (-) → 4 (BACK)
      Forward
      Battery positive (+) → 4 (BACK)
      Battery negative (-) → 3 (FWD)
      Backward

      Result 
      Result
      Proceed to
      OK (for LH Side)
      A
      OK (for RH Side)
      B
      NG (for LH Side)
      C
      NG (for RH Side)
      D



B
Go to step 4

C
REPLACE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH (Click here)

D
REPLACE NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH (Click here)
A


2. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEATBACK FRAME LH)
  1. Disconnect the d2 and d1 ECU connectors.

  1. Disconnect the d3 No. 3 seatback frame connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    d1-37 (SV2) - d3-5 (HLV)
    Always
    Below 1 Ω
    d1-37 (SV2) - Body ground
    Always
    10 kΩ or higher
    d1-19 (SRCL) - d3-2 (HLS)
    Always
    Below 1 Ω
    d1-19 (SRCL) - Body ground
    Always
    10 kΩ or higher
    d1-24 (SG2) - d3-6 (HLG)
    Always
    Below 1 Ω
    d1-24 (SG2) - Body ground
    Always
    10 kΩ or higher
    d2-1 (RCL+) - d3-3 (FWD)
    Always
    Below 1 Ω
    d2-1 (RCL+) - Body ground
    Always
    10 kΩ or higher
    d2-5 (RCL-) - d3-4 (BACK)
    Always
    Below 1 Ω
    d2-5 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK FOLD SEAT CONTROL ECU LH
B193667E18
  1. Remove the fold seat control ECU LH with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
d1-37 (SV2) - d1-24 (SG2)
Ignition switch off
Below 1 V
Ignition switch ON
5.5 to 8 V
d1-19 (SRCL) - d1-24 (SG2)
Motor is operating
Pulse generation
d2-1 (RCL+) - Body ground
Rear power seat switch LH forward
11 to 14 V
d2-5 (RCL-) - Body ground
Rear power seat switch LH backward
11 to 14 V

Text in Illustration 
*a
Component with harness connected
(Fold Seat Control ECU LH)


NG
REPLACE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEATBACK FRAME RH)
  1. Disconnect the c2 and c1 ECU connectors.

  1. Disconnect the c3 No. 3 seatback frame connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    c1-37 (SV2) - c3-5 (HLV)
    Always
    Below 1 Ω
    c1-37 (SV2) - Body ground
    Always
    10 kΩ or higher
    c1-19 (SRCL) - c3-2 (HLS)
    Always
    Below 1 Ω
    c1-19 (SRCL) - Body ground
    Always
    10 kΩ or higher
    c1-24 (SG2) - c3-6 (HLG)
    Always
    Below 1 Ω
    c1-24 (SG2) - Body ground
    Always
    10 kΩ or higher
    c2-1 (RCL+) - c3-3 (FWD)
    Always
    Below 1 Ω
    c2-1 (RCL+) - Body ground
    Always
    10 kΩ or higher
    c2-5 (RCL-) - c3-4 (BACK)
    Always
    Below 1 Ω
    c2-5 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOLD SEAT CONTROL ECU RH

5. CHECK FOLD SEAT CONTROL ECU RH
B193667E21
  1. Remove the fold seat control ECU RH with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
c1-37 (SV2) - c1-24 (SG2)
Ignition switch off
Below 1 V
Ignition switch ON
5.5 to 8 V
c1-19 (SRCL) - c1-24 (SG2)
Motor is operating
Pulse generation
c2-1 (RCL+) - Body ground
Rear power seat switch RH forward
11 to 14 V
c2-5 (RCL-) - Body ground
Rear power seat switch RH backward
11 to 14 V

Text in Illustration 
*a
Component with harness connected
(Fold Seat Control ECU RH)


NG
REPLACE NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Folding Motor Circuit (from Aug 2014)Reclining Motor Circuit (from Aug 2014) →