2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Folding Motor Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The fold seat control ECU receives switch operation signals from the No. 1 and No. 2 fold seat switches and activates the power seat motors. At this time, the Hall IC detects the actuation of the seat cushion and sends a seat cushion actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM

B246557E01

INSPECTION PROCEDURE


1. INSPECT SEAT LEG ASSEMBLY

  1. B239766E01
    for LH Side:
    1. Remove the No. 3 seat leg assembly LH (Click here).

    2. Check if the No. 3 seat leg moves smoothly when the battery is connected to the cushion motor connector terminals.

  1. for RH Side:

    1. Remove the rear No. 2 seat assembly (Click here).

    2. Check if the No. 2 seat leg moves smoothly when the battery is connected to the cushion motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 3 (FWD)
      Battery negative (-) → 4 (BACK)
      Forward
      Battery positive (+) → 4 (BACK)
      Battery negative (-) → 3 (FWD)
      Backward

      Result 
      Result
      Proceed to
      OK (for LH Side)
      A
      OK (for RH Side)
      B
      NG (for LH Side)
      C
      NG (for RH Side)
      D



B
Go to step 4

C
REPLACE NO. 3 SEAT LEG ASSEMBLY LH (Click here)

D
REPLACE NO. 2 SEAT LEG ASSEMBLY (Click here)
A


2. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEAT LEG)
  1. Disconnect the d2 and d1 ECU connectors.

  1. Disconnect the d4 No. 3 seat leg connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    d1-17 (SV1) - d4-5 (HLV)
    Always
    Below 1 Ω
    d1-17 (SV1) - Body ground
    Always
    10 kΩ or higher
    d1-18 (SFLD) - d4-2 (HLS)
    Always
    Below 1 Ω
    d1-18 (SFLD) - Body ground
    Always
    10 kΩ or higher
    d1-25 (SG1) - d4-6 (HLG)
    Always
    Below 1 Ω
    d1-25 (SG1) - Body ground
    Always
    10 kΩ or higher
    d2-8 (FLD+) - d4-3 (FWD)
    Always
    Below 1 Ω
    d2-8 (FLD+) - Body ground
    Always
    10 kΩ or higher
    d2-7 (FLD-) - d4-4 (BACK)
    Always
    Below 1 Ω
    d2-7 (FLD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK FOLD SEAT CONTROL ECU LH
  1. Remove the fold seat control ECU LH with its connectors still connected (Click here).

  1. B193667E17
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    d1-17 (SV1) - d1-25 (SG1)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    5.5 to 8 V
    d1-18 (SFLD) - d1-25 (SG1)
    Motor is operating
    Pulse generation
    d2-8 (FLD+) - Body ground
    No. 1 or No. 2 fold seat switch LH fold
    11 to 14 V
    d2-7 (FLD-) - Body ground
    No. 1 or No. 2 fold seat switch LH return
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Fold Seat Control ECU LH)



NG
REPLACE NO. 3 SEAT LEG ASSEMBLY LH (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 SEAT LEG)
  1. Disconnect the c2 and c1 ECU connectors.

  1. Disconnect the c4 No. 2 seat leg connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    c1-17 (SV1) - c4-5 (HLV)
    Always
    Below 1 Ω
    c1-17 (SV1) - Body ground
    Always
    10 kΩ or higher
    c1-18 (SFLD) - c4-2 (HLS)
    Always
    Below 1 Ω
    c1-18 (SFLD) - Body ground
    Always
    10 kΩ or higher
    c1-25 (SG1) - c4-6 (HLG)
    Always
    Below 1 Ω
    c1-25 (SG1) - Body ground
    Always
    10 kΩ or higher
    c2-8 (FLD+) - c4-3 (FWD)
    Always
    Below 1 Ω
    c2-8 (FLD+) - Body ground
    Always
    10 kΩ or higher
    c2-7 (FLD-) - c4-4 (BACK)
    Always
    Below 1 Ω
    c2-7 (FLD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK FOLD SEAT CONTROL ECU RH
  1. Remove the fold seat control ECU RH with its connectors still connected (Click here).

  1. B193667E20
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    c1-17 (SV1) - c1-25 (SG1)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    5.5 to 8 V
    c1-18 (SFLD) - c1-25 (SG1)
    Motor is operating
    Pulse generation
    c2-8 (FLD+) - Body ground
    No. 1 or No. 2 fold seat switch RH fold
    11 to 14 V
    c2-7 (FLD-) - Body ground
    No. 1 or No. 2 fold seat switch RH return
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Fold Seat Control ECU RH)



NG
REPLACE NO. 2 SEAT LEG ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Folding Motor Circuit (Aug 2013 – Jul 2014)Reclining Motor Circuit (Aug 2013 – Jul 2014) →