2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Rear Power Seat Switch Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the rear power seat switch is operated, a recline signal is sent to the fold seat control ECU. The ECU activates the power seat motor based on the signal from the rear power seat switch.

WIRING DIAGRAM

B239516E01

INSPECTION PROCEDURE


1. CHECK FOLD SEAT CONTROL ECU

  1. B243481E04
    Remove the fold seat control ECU with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH side 
    Tester Connection
    Condition
    Specified Condition
    d1-12 (RCLF) - Body ground
    Always
    11 to 14 V
    Rear power seat switch LH forward
    Below 1 V
    d1-13 (RCLR) - Body ground
    Always
    11 to 14 V
    Rear power seat switch LH backward
    Below 1 V
    RH side 
    Tester Connection
    Condition
    Specified Condition
    c1-12 (RCLF) - Body ground
    Always
    11 to 14 V
    Rear power seat switch RH forward
    Below 1 V
    c1-13 (RCLR) - Body ground
    Always
    11 to 14 V
    Rear power seat switch RH backward
    Below 1 V

    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *a
    Component with harness connected
    (Fold Seat Control ECU)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT REAR POWER SEAT SWITCH

  1. B239690E01
    Remove the rear power seat switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (FWD) - 6 (E)
    Always
    10 kΩ or higher
    Rear power seat switch forward
    Below 1 Ω
    5 (BACK) - 6 (E)
    Always
    10 kΩ or higher
    Rear power seat switch backward
    Below 1 Ω



NG
REPLACE REAR POWER SEAT SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH)
  1. *1: for LH Side
  2. *2: for RH Side
  1. Disconnect the d1*1 or c1*2 ECU connector.

  1. Disconnect the R11*1 or Q10*2 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    d1-12 (RCLF) - R11-4 (FWD)
    Always
    Below 1 Ω
    d1-12 (RCLF) - Body ground
    Always
    10 kΩ or higher
    d1-13 (RCLR) - R11-5 (BACK)
    Always
    Below 1 Ω
    d1-13 (RCLR) - Body ground
    Always
    10 kΩ or higher
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    c1-12 (RCLF) - Q10-4 (FWD)
    Always
    Below 1 Ω
    c1-12 (RCLF) - Body ground
    Always
    10 kΩ or higher
    c1-13 (RCLR) - Q10-5 (BACK)
    Always
    Below 1 Ω
    c1-13 (RCLR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FOLD SEAT CONTROL ECU (Click here)


← Rear Power Seat Switch Circuit (Aug 2013 – Jul 2014)PRECAUTION (from Aug 2013) →