2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

Rear Window Defogger System does not Operate

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the rear window defogger switch is turned on, a rear window defogger activation request signal is sent via the LIN communication line to the air conditioning amplifier.

WIRING DIAGRAM

B243039E01

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. Since the window defogger system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOGGER RELAY [REAR])
  1. Using the intelligent tester, perform the Active Test (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    DEF relay operation
    OFF/ON
    -

    OK:
    The DEF relay operates normally.



NG
Go to step 3
OK


2. REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY
  1. Temporarily replace the heater control with a new or normally functioning one (Click here).

  1. Check the rear defogger function.

    OK:
    The window defogger function operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (INTEGRATION CONTROL AND PANEL ASSEMBLY IS DEFECTIVE)

3. INSPECT DEF RELAY

  1. B242124E01
    Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage applied between terminals 1 and 2
    Below 1 Ω
    3 - 5
    Battery voltage not applied between terminals 1 and 2
    10 kΩ or higher



NG
REPLACE DEF RELAY
OK


4. CHECK HARNESS AND CONNECTOR (DEF RELAY - BATTERY AND BODY GROUND)

  1. B242123E01
    Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DEF relay terminal 2 - Body ground
    Ignition switch off
    Below 1 V
    DEF relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V
    DEF relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DEF Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - DEF RELAY AND BODY GROUND)
  1. Disconnect the G25 air conditioning amplifier connector.

  1. Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEF relay terminal 1 - G25-38 (RDEF)
    Always
    Below 1 Ω
    G25-14 (GND) - Body ground
    Always
    Below 1 Ω
    G25-38 (RDEF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E183334E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G25-38 (RDEF) - G25-14 (GND)
    Ignition switch ON, defogger switch on
    11 to 14 V
    G25-38 (RDEF) - G25-14 (GND)
    Ignition switch ON, defogger switch off
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS - DEF RELAY AND BODY GROUND)
  1. Disconnect the Y2*1 or X7*2 and X8*2 back door glass (window defogger wire) connectors.

    1. *1: w/ Glass Hatch Opener System
    2. *2: w/o Glass Hatch Opener System

  1. Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Glass Hatch Opener System 
    Tester Connection
    Condition
    Specified Condition
    DEF relay terminal 3 - Y2-2
    Always
    Below 1 Ω
    Y2-1 - Body ground
    Always
    Below 1 Ω
    Y2-2 - Body ground
    Always
    10 kΩ or higher
    w/o Glass Hatch Opener System 
    Tester Connection
    Condition
    Specified Condition
    DEF relay terminal 3 - X7-1
    Always
    Below 1 Ω
    X8-1 - Body ground
    Always
    Below 1 Ω
    X7-1 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/ Glass Hatch Opener System)
    A
    OK (w/o Glass Hatch Opener System)
    B
    NG
    C



B
REPLACE BACK DOOR GLASS (WINDOW DEFOGGER WIRE) (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BACK DOOR GLASS (WINDOW DEFOGGER WIRE) (Click here)


← DATA LIST / ACTIVE TEST (from Aug 2013)Rear Window Defogger System does not Operate (from Aug 2014) →