Rear Window Defogger System does not Operate
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the rear window defogger switch is turned on, a rear window defogger activation request signal is sent via the LIN communication line to the air conditioning amplifier.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Since the window defogger system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOGGER RELAY [REAR]) |
Using the intelligent tester, perform the Active Test (Click here).
Air Conditioner Tester Display
Test Part
Control Range
Diagnostic Note
Defogger Relay (Rear)
DEF relay operation
OFF/ON
-
- OK:
- The DEF relay operates normally.
|
|
||||
| OK | |
| 2. REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY |
Temporarily replace the heater control with a new or normally functioning one (Click here).
Check the rear defogger function.
- OK:
- The window defogger function operates normally.
|
|
||||
| OK | ||
| ||
| 3. INSPECT DEF RELAY |
Remove the DEF relay from the engine room relay block, junction block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage applied between terminals 1 and 2
Below 1 Ω
3 - 5
Battery voltage not applied between terminals 1 and 2
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (DEF RELAY - BATTERY AND BODY GROUND) |
Remove the DEF relay from the engine room relay block, junction block.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
DEF relay terminal 2 - Body ground
Ignition switch off
Below 1 V
DEF relay terminal 2 - Body ground
Ignition switch ON
11 to 14 V
DEF relay terminal 5 - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to DEF Relay)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - DEF RELAY AND BODY GROUND) |
Disconnect the G25 air conditioning amplifier connector.
Remove the DEF relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
DEF relay terminal 1 - G25-38 (RDEF)
Always
Below 1 Ω
G25-14 (GND) - Body ground
Always
Below 1 Ω
G25-38 (RDEF) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY |
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G25-38 (RDEF) - G25-14 (GND)
Ignition switch ON, defogger switch on
11 to 14 V
G25-38 (RDEF) - G25-14 (GND)
Ignition switch ON, defogger switch off
Below 1 V
Text in Illustration *a
Component with harness connected
(Air Conditioning Amplifier Assembly)
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS - DEF RELAY AND BODY GROUND) |
Disconnect the Y2*1 or X7*2 and X8*2 back door glass (window defogger wire) connectors.
- *1: w/ Glass Hatch Opener System
- *2: w/o Glass Hatch Opener System
- *1: w/ Glass Hatch Opener System
Remove the DEF relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
w/ Glass Hatch Opener System Tester Connection
Condition
Specified Condition
DEF relay terminal 3 - Y2-2
Always
Below 1 Ω
Y2-1 - Body ground
Always
Below 1 Ω
Y2-2 - Body ground
Always
10 kΩ or higher
w/o Glass Hatch Opener System Tester Connection
Condition
Specified Condition
DEF relay terminal 3 - X7-1
Always
Below 1 Ω
X8-1 - Body ground
Always
Below 1 Ω
X7-1 - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (w/ Glass Hatch Opener System)
A
OK (w/o Glass Hatch Opener System)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
