2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

B2342 Switch Failure

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

This DTC is stored when the sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2342
The sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more.
  1. Sliding roof drive gear sub-assembly (Sliding roof ECU)
  2. Map light assembly (Sliding roof switch)
  3. Harness or connector

WIRING DIAGRAM

B243239E01

INSPECTION PROCEDURE

NOTICE:
When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (Click here).


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2342 is output
    A
    DTC B2342 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF)
  1. Using the intelligent tester, read the Data List (Click here).

    Sliding Roof 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch Failure (Past)
    Slide open switch failure signal (Past) / ON or OFF
    ON: Slide open switch signal failure (Past)
    OFF: No slide open switch signal failure (Past)
    -
    Close Switch Failure (Past)
    Slide close switch failure signal (Past) / ON or OFF
    ON: Slide close switch signal failure (Past)
    OFF: No slide close switch signal failure (Past)
    -
    Up Switch Failure (Past)
    Tilt up switch failure signal (Past) / ON or OFF
    ON: Tilt up switch signal failure (Past)
    OFF: No tilt up switch signal failure (Past)
    -
    Down Switch Failure (Past)
    Tilt down switch failure signal (Past) / ON or OFF
    ON: Tilt down switch signal failure (Past)
    OFF: No tilt down switch signal failure (Past)
    -
    Open Switch Failure (Current)
    Slide open switch failure signal (Current) / ON or OFF
    ON: Slide open switch signal failure (Current)
    OFF: No slide open switch signal failure (Current)
    -
    Close Switch Failure (Current)
    Slide close switch failure signal (Current) / ON or OFF
    ON: Slide close switch signal failure (Current)
    OFF: No slide close switch signal failure (Current)
    -
    Up Switch Failure (Current)
    Tilt up switch failure signal (Current) / ON or OFF
    ON: Tilt up switch signal failure (Current)
    OFF: No tilt up switch signal failure (Current)
    -
    Down Switch Failure (Current)
    Tilt down switch failure signal (Current) / ON or OFF
    ON: Tilt down switch signal failure (Current)
    OFF: No tilt down switch signal failure (Current)
    -

    OK:
    "OFF" appears on the intelligent tester screen.



NG
Go to step 3
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)

3. INSPECT MAP LIGHT ASSEMBLY
B240415E01
  1. Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (IG) - 23 (IG3)
    Always
    Below 1 Ω
    24 (UP) - 5 (GND3)
    Tilt up switch pressed
    Below 1 Ω
    24 (UP) - 5 (GND3)
    Tilt up switch not pressed
    10 kΩ or higher
    25 (DOWN) - 5 (GND3)
    Tilt down switch pressed
    Below 1 Ω
    25 (DOWN) - 5 (GND3)
    Tilt down switch not pressed
    10 kΩ or higher
    27 (OPN) - 5 (GND3)
    Slide open switch pressed
    Below 1 Ω
    27 (OPN) - 5 (GND3)
    Slide open switch not pressed
    10 kΩ or higher
    28 (CLS) - 5 (GND3)
    Slide close switch pressed
    Below 1 Ω
    28 (CLS) - 5 (GND3)
    Slide close switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly)



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH, BATTERY AND BODY GROUND)
  1. Disconnect the W2 ECU connector.

  1. Disconnect the W7 switch connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-10 (UP) - W7-24 (UP)
    Always
    Below 1 Ω
    W2-8 (DWN) - W7-25 (DOWN)
    Always
    Below 1 Ω
    W2-7 (OPN) - W7-27 (OPN)
    Always
    Below 1 Ω
    W2-9 (CLS) - W7-28 (CLS)
    Always
    Below 1 Ω
    W7-5 (GND3) - Body ground
    Always
    Below 1 Ω
    W2-2 (E) - Body ground
    Always
    Below 1 Ω
    W2-5 (IG) - W7-23 (IG3)
    Always
    Below 1 Ω
    W2-10 (UP) or W7-24 (UP) - Body ground
    Always
    10 kΩ or higher
    W2-8 (DWN) or W7-25 (DOWN) - Body ground
    Always
    10 kΩ or higher
    W2-7 (OPN) or W7-27 (OPN) - Body ground
    Always
    10 kΩ or higher
    W2-9 (CLS) or W7-28 (CLS) - Body ground
    Always
    10 kΩ or higher
    W2-5 (IG) or W7-23 (IG3) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W7-8 (IG) - Body ground
    Ignition switch off
    Below 1 V
    W7-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)


← B2341 Sensor (Motor) Failure (+ B2344) (from Aug 2013)B2343 Position Initialization Incomplete (from Aug 2013) →