2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

B2343 Position Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

This DTC is stored when the sliding roof drive gear sub-assembly has not been initialized.
DTC Code
DTC Detection Condition
Trouble Area
B2343
The sliding roof drive gear sub-assembly has not been initialized.
  1. Sliding roof drive gear sub-assembly (Sliding roof ECU)
  2. Map light assembly (Sliding roof switch)
  3. Harness or connector

WIRING DIAGRAM

B243239E01

INSPECTION PROCEDURE

NOTICE:
When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (Click here).


1. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
  1. Check that the sliding roof drive gear sub-assembly can be initialized (Click here).

    OK:
    The sliding roof drive gear sub-assembly can be initialized.



NG
Go to step 3
OK


2. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2343 is not output
    A
    DTC B2343 is output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)
A

END

3. INSPECT MAP LIGHT ASSEMBLY
B240415E01
  1. Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (IG) - 23 (IG3)
    Always
    Below 1 Ω
    24 (UP) - 5 (GND3)
    Tilt up switch pressed
    Below 1 Ω
    24 (UP) - 5 (GND3)
    Tilt up switch not pressed
    10 kΩ or higher
    25 (DOWN) - 5 (GND3)
    Tilt down switch pressed
    Below 1 Ω
    25 (DOWN) - 5 (GND3)
    Tilt down switch not pressed
    10 kΩ or higher
    27 (OPN) - 5 (GND3)
    Slide open switch pressed
    Below 1 Ω
    27 (OPN) - 5 (GND3)
    Slide open switch not pressed
    10 kΩ or higher
    28 (CLS) - 5 (GND3)
    Slide close switch pressed
    Below 1 Ω
    28 (CLS) - 5 (GND3)
    Slide close switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly)



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH, BATTERY AND BODY GROUND)
  1. Disconnect the W2 ECU connector.

  1. Disconnect the W7 switch connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-10 (UP) - W7-24 (UP)
    Always
    Below 1 Ω
    W2-8 (DWN) - W7-25 (DOWN)
    Always
    Below 1 Ω
    W2-7 (OPN) - W7-27 (OPN)
    Always
    Below 1 Ω
    W2-9 (CLS) - W7-28 (CLS)
    Always
    Below 1 Ω
    W7-5 (GND3) - Body ground
    Always
    Below 1 Ω
    W2-2 (E) - Body ground
    Always
    Below 1 Ω
    W2-5 (IG) - W7-23 (IG3)
    Always
    Below 1 Ω
    W2-10 (UP) or W7-24 (UP) - Body ground
    Always
    10 kΩ or higher
    W2-8 (DWN) or W7-25 (DOWN) - Body ground
    Always
    10 kΩ or higher
    W2-7 (OPN) or W7-27 (OPN) - Body ground
    Always
    10 kΩ or higher
    W2-9 (CLS) or W7-28 (CLS) - Body ground
    Always
    10 kΩ or higher
    W2-5 (IG) or W7-23 (IG3) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W7-8 (IG) - Body ground
    Ignition switch off
    Below 1 V
    W7-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)


← B2342 Switch Failure (from Aug 2013)Remote Control System does not Operate (Aug 2013 – Jul 2014) →