B1449/49 Rear Air Outlet Damper Control Servo Motor Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The rear mode damper servo sub-assembly sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air outlet damper to any position, which controls the air outlet modes.The air conditioning amplifier assembly communicates with the servo through the No. 2 air conditioning harness.
- HINT:
- Confirm that there are no mechanical problems because this DTC may be stored when either a damper link or damper is mechanically locked.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1449/49 |
Rear air outlet damper position does not change when the air conditioning amplifier assembly operates the rear mode damper servo sub-assembly. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1449/49 is not output
A
DTC B1449/49 is output
B
DTC B1449/49 and B1497/97 are output
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. READ VALUE USING INTELLIGENT TESTER (REAR MODE DAMPER SERVO) |
Use the Data List to check if the rear mode damper servo sub-assembly is functioning properly (Click here).
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Outlet Servo Pulse (R)
Rear mode damper servo sub-assembly target pulse / Min.: 0, Max.: 255
83 (pulse): FACE
41 (pulse): B/L
7 (pulse): FOOT
-
Air Mix Servo Actual Pulse (R)
Rear mode damper servo sub-assembly actual pulse / Min.: 0, Max.: 255
83 (pulse): FACE
41 (pulse): B/L
7 (pulse): FOOT
-
- OK:
- The display is as specified in the normal condition column.
Result Result
Proceed to
OK (When troubleshooting according to the DTC)
A
OK (When troubleshooting according to Problem Symptoms Table
B
Both target pulse and actual pulse do not display
C
Target pulse displays normally, but actual pulse does not display
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1449 is not output.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER) |
Disconnect the Q13 harness connector.
Disconnect the G24 amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Q13-3 (RBUS) - G24-1 (RBUS)
Always
Below 1 Ω
Q13-4 (RBBU) - G24-23 (RBBU)
Always
Below 1 Ω
Q13-2 (RBUG) - G24-21 (RBUG)
Always
Below 1 Ω
G24-1 (RBUS) - Body ground
Always
10 kΩ or higher
G24-23 (RBBU) - Body ground
Always
10 kΩ or higher
G24-21 (RBUG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY |
Replace the rear mode damper servo sub-assembly (Click here).
- HINT:
- Since the rear mode damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the rear mode damper servo sub-assembly with a new or normally functioning one.
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1449 is not output.
|
|
||||
| OK | ||
| ||
| 6. CHECK AIR CONDITIONING HARNESS ASSEMBLY |
Temporarily replace the air conditioning harness assembly with a new or normally functioning one (Click here).
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1449 is not output.
|
|
||||
| OK | ||
| ||
