Short in CAN Bus Lines
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.| Symptom |
Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω. |
|
- *1: except 5L-E
- *2: for 5L-E
- *3: for 2TR-FE, 5L-E
- *4: for 1GR-FE, 1KD-FTV
- *5: w/ Network Gateway ECU
- *6: w/ Vehicle Stability Control System
- *7: w/ Audio and Visual System (for Radio and Display Type)
WIRING DIAGRAM






INSPECTION PROCEDURE
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE) |
Disconnect the G94 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G48-6 (CANH) - G48-14 (CANL)
Ignition switch off
1 MΩ or higher
Text in Illustration *a
Front view of DLC3
|
|
||||
| OK | |
| 3. CONNECT CONNECTOR |
Reconnect the G94 No. 3 junction connector.
| NEXT | |
| 4. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE) |
Disconnect the G97 No. 1 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G48-6 (CANH) - G48-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of DLC3
|
|
||||
| OK | |
| 5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G97-2 (CANH) - G97-13 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
|
|
||||
| OK | |
| 6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
- NOTICE:
- For vehicles without a network gateway ECU, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Air Conditioning Amplifier Assembly)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G97-3 (CANH) - G97-14 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
|
|
||||
| OK | |
| 7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G97-4 (CANH) - G97-15 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
|
|
||||
| OK | |
| 8. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY) |
- NOTICE:
- For vehicles without a vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - ECM or No. 4 Junction Connector)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G97-5 (CANH) - G97-16 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
|
|
||||
| OK | |
| 9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G97-6 (CANH) - G97-17 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
Result Result
Proceed to
OK
A
NG (for 1GR-FE)
B
NG (for 1KD-FTV)
C
NG (for 2TR-FE, 5L-E)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 10. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 11. CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU) |
Disconnect the G53 four wheel drive control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G53-19 (CANH) - G53-20 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Four Wheel Drive Control ECU)
|
|
||||
| OK | ||
| ||
| 12. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 13. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU) |
Disconnect the G155 network gateway ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G155-16 (CA1H) - G155- 15 (CA1L)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Network Gateway ECU)
|
|
||||
| OK | ||
| ||
| 14. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 15. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect the G25 air conditioning amplifier assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G25-11 (CANH) - G25-12 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
|
|
||||
| OK | ||
| ||
| 16. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 17. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY) |
Disconnect the G46 power steering ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G46-1 (CANH) - G46-2 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Power Steering ECU Assembly)
|
|
||||
| OK | ||
| ||
| 18. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 19. CHECK FOR SHORT IN CAN BUS WIRES (ECM) |
Disconnect the G56 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G56-32 (CANH) - G56-31 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 20. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 21. CHECK FOR SHORT IN CAN BUS WIRES (ECM) |
Disconnect the G58 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G58-35 (CANH) - G58-36 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 22. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR) |
Disconnect the A72 No. 4 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A72-9 (CANH) - A72-20 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
|
|
||||
| OK | |
| 24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A72-11 (CANH) - A72-22 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
|
|
||||
| OK | |
| 25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - ECM OR NO. 6 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A72-10 (CANH) - A72-21 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
Result Result
Proceed to
OK
A
NG (for 2TR-FE)
B
NG (for 5L-E)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 26. CONNECT CONNECTOR |
Reconnect the A72 No. 4 junction connector.
| NEXT | |
| 27. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU) |
Disconnect the A6 brake actuator assembly (skid control ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A6-25 (CANH) - A6-14 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
|
|
||||
| OK | ||
| ||
| 28. CONNECT CONNECTOR |
Reconnect the A72 No. 4 junction connector.
| NEXT | |
| 29. CHECK FOR SHORT IN CAN BUS WIRES (ECM) |
Disconnect the G60 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G60-34 (CANH) - G60-33 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 30. CONNECT CONNECTOR |
Reconnect the A72 No. 4 junction connector.
| NEXT | |
| 31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR) |
Disconnect the G101 No. 6 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G101-3 (CANH) - G101-2 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
|
|
||||
| OK | ||
| ||
| 32. CONNECT CONNECTOR |
Reconnect the G97 No. 1 junction connector.
| NEXT | |
| 33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR) |
Disconnect the G100 No. 2 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G100-1 (CANH) - G100- 12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | |
| 34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G48-6 (CANH) - G48-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of DLC3
|
|
||||
| OK | |
| 35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
- NOTICE:
- For vehicles without an audio and visual system (for radio and display type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Steering Angle Sensor)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G100-2 (CANH) - G100- 13 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | |
| 36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
- NOTICE:
- For vehicles without a vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Yaw Rate Sensor Assembly)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G100-3 (CANH) - G100- 14 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | |
| 37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G100-4 (CANH) - G100- 15 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | |
| 38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G100-5 (CANH) - G100- 16 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | ||
| ||
| 39. CONNECT CONNECTOR |
Reconnect the G100 No. 2 junction connector.
| NEXT | |
| 40. CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY) |
Disconnect the H51 radio and display receiver assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
H51-9 (CANH) - H51-10 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Front view of wire harness connector
(to Radio and Display Receiver Assembly)
|
|
||||
| OK | ||
| ||
| 41. CONNECT CONNECTOR |
Reconnect the G100 No. 2 junction connector.
| NEXT | |
| 42. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR) |
Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G33-4 (CANH) - G33-3 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])
|
|
||||
| OK | ||
| ||
| 43. CONNECT CONNECTOR |
Reconnect the G100 No. 2 junction connector.
| NEXT | |
| 44. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY) |
Disconnect the G52 yaw rate sensor assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G52-3 (CANH) - G52-2 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Front view of wire harness connector
(to Yaw Rate Sensor Assembly)
|
|
||||
| OK | ||
| ||
| 45. CONNECT CONNECTOR |
Reconnect the G100 No. 2 junction connector.
| NEXT | |
| 46. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the G1 center airbag sensor assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G1-13 (CANH) - G1-22 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Front view of wire harness connector
(to Center Airbag Sensor Assembly)
|
|
||||
| OK | ||
| ||
| 47. CONNECT CONNECTOR |
Reconnect the G100 No. 2 junction connector.
| NEXT | |
| 48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Disconnect the G94 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G94-1 (CANH) - G94-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | |
| 49. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G94-3 (CANH) - G94-14 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | |
| 50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR OR COMBINATION METER ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
for 1GR-FE, 1KD-FTV Tester Connection
Switch Condition
Specified Condition
G94-6 (CANH) - G94-17 (CANL)
Ignition switch off
108 to 132 Ω
for 2TR-FE, 5L-E Tester Connection
Switch Condition
Specified Condition
G94-2 (CANH) - G94-13 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *A
for 1GR-FE, 1KD-FTV
*B
for 2TR-FE, 5L-E
*a
Rear view of wire harness connector
(to No. 3 Junction Connector)
Result Result
Proceed to
OK
A
NG (for 2TR-FE, 5L-E)
B
NG (for 1GR-FE, 1KD-FTV)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 51. CONNECT CONNECTOR |
Reconnect the G94 No. 3 junction connector.
| NEXT | |
| 52. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) |
Disconnect the G64 main body ECU (multiplex network body ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G64-14 (CANH) - G64-13 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
|
|
||||
| OK | ||
| ||
| 53. CONNECT CONNECTOR |
Reconnect the G94 No. 3 junction connector.
| NEXT | |
| 54. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY) |
Disconnect the G6 combination meter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G6-40 (CANH) - G6-39 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
|
|
||||
| OK | ||
| ||
| 55. CONNECT CONNECTOR |
Reconnect the G94 No. 3 junction connector.
| NEXT | |
| 56. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
Disconnect the A73 No. 5 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A73-9 (CANH) - A73-20 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
|
|
||||
| OK | |
| 57. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SKID CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A73-11 (CANH) - A73-22 (CANL)
Ignition switch off
200 Ω or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
|
|
||||
| OK | |
| 58. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A73-10 (CANH) - A73-21 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
|
|
||||
| OK | ||
| ||
| 59. CONNECT CONNECTOR |
Reconnect the A73 No. 5 junction connector.
| NEXT | |
| 60. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU) |
Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A7-11 (CANH) - A7-25 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *a
Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])
|
|
||||
| OK | ||
| ||
| 61. CONNECT CONNECTOR |
Reconnect the A73 No. 5 junction connector.
| NEXT | |
| 62. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY) |
Disconnect the G6 combination meter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G6-40 (CANH) - G6-39 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
|
|
||||
| OK | ||
| ||
