2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U1002 Lost Communication with Gateway Module (MS Bus)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.
  2. When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU (multiplex network body ECU) determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U1002 (CAN MS BUS)
Lost communication with the gateway module (MS bus).
  1. MS bus circuit
  2. Main body ECU (multiplex network body ECU) CAN main wire or connector
  3. Front power seat switch RH CAN branch wire or connector*1
  4. Multiplex tilt and telescopic ECU CAN branch wire or connector*2
  5. Driving support switch control ECU CAN branch wire or connector*3
  6. Main body ECU (multiplex network body ECU)
  7. Front power seat switch RH*1
  8. Multiplex tilt and telescopic ECU*2
  9. Driving monitor switch control ECU*3
  10. No. 2 junction connector
  11. No. 5 junction connector
  1. *1: w/ Seat Position Memory
  2. *2: for Power Tilt and Power Telescopic Steering Column
  3. *3: w/ Multi-function Switch

WIRING DIAGRAM

C294685E03

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)

  1. C216700E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance: Malfunction
    G103-3 (CANP) - G103-2 (CANN)
    Engine switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    G103-3 (CANP) - G103-2 (CANN)
    Engine switch off
    54 to 69 Ω
    Higher than 70 Ω: Open in CAN main bus line
    G103-3 (CANP) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G103-2 (CANN) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G103-3 (CANP) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    G103-2 (CANN) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connector
    (No. 5 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main bus line
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 9

C
Go to step 24
A


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)
C238894E01
  1. Disconnect the G133 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-4 (CANH) - G133-15 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C238894E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-6 (CANH) - G133-17 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 7
OK

REPLACE NO. 2 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 2 JUNCTION CONNECTOR)
C216701E01
  1. Disconnect the G63 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G63-9 (CANP) - G63-10 (CANN)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

7. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C210060E08
    Disconnect the G103 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G103-3 (CANP) - G103-2 (CANN)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 5 JUNCTION CONNECTOR

9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH RH)

NOTICE:
For vehicles without a seat position memory, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Multiplex Tilt and Telescopic ECU)".

  1. C218087E95
    Disconnect the G133 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-2 (CANH) - G133-13 (CANL)
    Engine switch off
    200 Ω or higher
    G133-2 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G133-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 14
OK


10. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NOTICE:
For vehicles without a power tilt and power telescopic steering column, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Driving Support Switch Control ECU)".

  1. C218087E96
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-3 (CANH) - G133-14 (CANL)
    Engine switch off
    200 Ω or higher
    G133-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G133-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 16
OK


11. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)

NOTICE:
For vehicles without a multi-function switch, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Main Body ECU)".

  1. C218087E97
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-5 (CANH) - G133-16 (CANL)
    Engine switch off
    200 Ω or higher
    G133-5 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-16 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-5 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G133-16 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 18
OK


12. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C218087E98
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-4 (CANH) - G133-15 (CANL)
    Engine switch off
    108 to 132 Ω
    G133-4 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-15 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-4 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G133-15 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 20
OK


13. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C218087E99
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G133-6 (CANH) - G133-17 (CANL)
    Engine switch off
    108 to 132 Ω
    G133-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-17 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G133-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G133-17 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 22
OK

REPLACE NO. 2 JUNCTION CONNECTOR

14. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


15. CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH RH)

  1. C210055E01
    Disconnect the a5 front power seat switch RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a5-8 (CANP) - a5-7 (CANN)
    Engine switch off
    54 to 69 Ω
    a5-8 (CANP) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    a5-7 (CANN) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    a5-8 (CANP) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    a5-7 (CANN) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Front Power Seat Switch RH)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT POWER SEAT SWITCH RH (CANP, CANN)
OK

REPLACE FRONT POWER SEAT SWITCH RH (Click here)

16. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


17. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)

  1. C216734E01
    Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G116-5 (CANP) - G116-14 (CANN)
    Engine switch off
    54 to 69 Ω
    G116-5 (CANP) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G116-14 (CANN) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G116-5 (CANP) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G116-14 (CANN) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

18. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


19. CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU)

  1. for Automatic Transmission:

    1. C288333E01
      Disconnect the G163 driving support switch control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      G163-2 (CANP) - G163-3 (CANN)
      Engine switch off
      54 to 69 Ω
      G163-2 (CANP) - G48-4 (CG)
      Engine switch off
      200 Ω or higher
      G163-3 (CANN) - G48-4 (CG)
      Engine switch off
      200 Ω or higher
      G163-2 (CANP) - G48-16 (BAT)
      Engine switch off
      6 kΩ or higher
      G163-3 (CANN) - G48-16 (BAT)
      Engine switch off
      6 kΩ or higher

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Driving Support Switch Control ECU)
      *b
      Front view of DLC3

  1. for Manual Transmission:

    1. C216736E03
      Disconnect the G76 driving support switch control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      G76-9 (CANP) - G76-10 (CANN)
      Engine switch off
      54 to 69 Ω
      G76-9 (CANP) - G48-4 (CG)
      Engine switch off
      200 Ω or higher
      G76-10 (CANN) - G48-4 (CG)
      Engine switch off
      200 Ω or higher
      G76-9 (CANP) - G48-16 (BAT)
      Engine switch off
      6 kΩ or higher
      G76-10 (CANN) - G48-16 (BAT)
      Engine switch off
      6 kΩ or higher

      Text in Illustration 
      *a
      Rear view of wire harness connector
      (to Driving Support Switch Control ECU)
      *b
      Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT SWITCH CONTROL ECU (CANP, CANN)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)

20. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. C216735E01
    Disconnect the G63 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G63-9 (CANP) - G63-10 (CANN)
    Engine switch off
    108 to 132 Ω
    G63-9 (CANP) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G63-10 (CANN) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G63-9 (CANP) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G63-10 (CANN) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

22. CONNECT CONNECTOR
  1. Reconnect the G133 No. 2 junction connector.


NEXT


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)

  1. C242753E12
    Disconnect the G103 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G103-3 (CANP) - G103-2 (CANN)
    Engine switch off
    108 to 132 Ω
    G103-3 (CANP) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G103-2 (CANN) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G103-3 (CANP) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G103-2 (CANN) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 5 JUNCTION CONNECTOR

24. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

  1. Connect the cable to the negative (-) battery terminal.C215398E03

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G63-3 (GND2) - Body ground
    Always
    Below 1 Ω
    A-11 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    Always
    11 to 14 V
    A-29 (ACC) - Body ground
    Engine switch on (ACC)
    11 to 14 V
    A-32 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← U1002 Lost Communication with Gateway Module (Power Management2) (from Aug 2014)U1002 Lost Communication with Gateway Module (MS Bus) (from Aug 2014) →