B1825/56 Short in Side Squib LH Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- B1826/56 Open in Side Squib LH Circuit
- B1827/56 Short to GND in Side Squib LH Circuit
- B1828/56 Short to B+ in Side Squib LH Circuit
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The side squib LH circuit consists of the center airbag sensor and front seat airbag LH.The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the side squib LH circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1825/56 |
One of the following conditions is met:
|
|
| B1826/56 |
One of the following conditions is met:
|
|
| B1827/56 |
One of the following conditions is met:
|
|
| B1828/56 |
One of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- HINT:
- To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).
| 1. CHECK FRONT SEAT AIRBAG ASSEMBLY LH (SIDE SQUIB LH) |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front seat airbag LH.
Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front seat airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1825, B1826, B1827 or B1828 is not output.
- HINT:
- Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.
Text in Illustration *1
Side Squib LH
*2
Center Airbag Sensor
*3
Connector C
*4
SST
*a
Front view of wire harness connector
(to Side Squib LH)
*b
Color: Red
|
|
||||
| OK | ||
| ||
| 2. CHECK NO. 2 FLOOR WIRE (SIDE SQUIB LH CIRCUIT) |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
R6-1 (SFL+) - Body ground
Ignition switch ON
Below 1 V
R6-2 (SFL-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R6-1 (SFL+) - R6-2 (SFL-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R6-1 (SFL+) - R6-2 (SFL-)
Always
1 MΩ or higher
R6-1 (SFL+) - Body ground
Always
1 MΩ or higher
R6-2 (SFL-) - Body ground
Always
1 MΩ or higher
| *1 |
Side Squib LH |
| *2 |
No. 2 Floor Wire |
| *3 |
Center Airbag Sensor |
| *4 |
Connector C |
| *a |
Front view of wire harness connector (to Side Squib LH) |
|
|
||||
| OK | |
| 3. CHECK CENTER AIRBAG SENSOR |
Connect the connectors to the front seat airbag LH and center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1825, B1826, B1827 or B1828 is not output.
- HINT:
- Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.
Text in Illustration *1
Side Squib LH
*2
Center Airbag Sensor
|
|
||||
| OK | ||
| ||
