2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1830/57 Short in Curtain Shield Squib RH Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor and curtain shield airbag RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1830/57
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the curtain shield squib RH circuit during the primary check.
  2. A curtain shield squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1831/57
One of the following conditions is met:
  1. The center airbag sensor detects open circuit signal in the curtain shield squib RH circuit for 2 seconds.
  2. A curtain shield squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1832/57
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.
  2. A curtain shield squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1833/57
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.
  2. A curtain shield squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C174615E28
C174615E45

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



A
Go to step 6
B


2. CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)

  1. C217719E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the curtain shield airbag RH.

  1. Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832 or B1833 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Curtain Shield Squib RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Curtain Shield Squib RH)



NG
Go to step 3
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH (Click here)

3. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. C214775E01
    Check that the floor wire connector (on the curtain shield airbag RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Curtain Shield Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (CURTAIN SHIELD AIRBAG RH - CENTER AIRBAG SENSOR)

  1. C216072E02
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q6-1 (ICR+) - Body ground
    Ignition switch ON
    Below 1 V
    Q6-2 (ICR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q6-1 (ICR+) - Q6-2 (ICR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q6-1 (ICR+) - Q6-2 (ICR-)
    Always
    1 MΩ or higher
    Q6-1 (ICR+) - Body ground
    Always
    1 MΩ or higher
    Q6-2 (ICR-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Curtain Shield Squib RH
*2
Floor Wire
*3
Center Airbag Sensor
*4
Connector C
*a
Front view of wire harness connector
(to Curtain Shield Squib RH)


NG
REPLACE FLOOR WIRE
OK


5. CHECK CENTER AIRBAG SENSOR

  1. C146261E37
    Connect the connectors to the curtain shield airbag RH and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832 or B1833 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Curtain Shield Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

6. CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)

  1. C217720E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the curtain shield airbag RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832 or B1833 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Curtain Shield Squib RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Curtain Shield Squib RH)



NG
Go to step 7
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH (Click here)

7. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. C214775E01
    Check that the floor wire connector (on the curtain shield airbag RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Curtain Shield Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE FLOOR WIRE
OK


8. CHECK FLOOR WIRE (CURTAIN SHIELD AIRBAG RH - CENTER AIRBAG SENSOR)

  1. C217721E01
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q29-1 (ICR+) - Body ground
    Ignition switch ON
    Below 1 V
    Q29-2 (ICR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q29-1 (ICR+) - Q29-2 (ICR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q29-1 (ICR+) - Q29-2 (ICR-)
    Always
    1 MΩ or higher
    Q29-1 (ICR+) - Body ground
    Always
    1 MΩ or higher
    Q29-2 (ICR-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Curtain Shield Squib RH
*2
Floor Wire
*3
Center Airbag Sensor
*4
Connector C
*a
Front view of wire harness connector
(to Curtain Shield Squib RH)


NG
REPLACE FLOOR WIRE
OK


9. CHECK CENTER AIRBAG SENSOR

  1. C146261E37
    Connect the connectors to the curtain shield airbag RH and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832 or B1833 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Curtain Shield Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1825/56 Short in Side Squib LH Circuit (+ B1826/56, B1827/56, B1828/56) (from Aug 2014)B1830/57 Short in Curtain Shield Squib RH Circuit (+ B1831/57, B1832/57, B1833/57) (from Aug 2014) →