2013-2015 Land Cruiser Prado · Service Manual Suspension

C1731/31 FR Damping Force Control Actuator Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The absorber control actuator switches the damping force depending on the suspension control ECU signals.
DTC Code
DTC Detection Condition
Trouble Area
C1731/31
Either condition is met:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Front absorber control actuator RH
  3. Suspension control ECU
C1732/32
Either condition is met:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Front absorber control actuator LH
  3. Suspension control ECU
C1733/33
Either condition is met:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Rear absorber control actuator RH (Rear shock absorber assembly)
  3. Suspension control ECU
C1734/34
Either condition is met:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Rear absorber control actuator LH (Rear shock absorber assembly)
  3. Suspension control ECU

WIRING DIAGRAM

C214503E02

INSPECTION PROCEDURE

NOTICE:
When replacing the suspension control ECU, perform registration (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DAMPER STEP)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Damper Step FR
    Changes damper step (Front RH)
    1 to 17 step
    The shock absorber hardens as the damper step increases.
    Damper Step FL
    Changes damper step (Front LH)
    1 to 17 step
    The shock absorber hardens as the damper step increases.
    Damper Step RR
    Changes damper step (Rear RH)
    1 to 17 step
    The shock absorber hardens as the damper step increases.
    Damper Step RL
    Changes damper step (Rear LH)
    1 to 17 step
    The shock absorber hardens as the damper step increases.

    OK:
    The absorber control actuator operates.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. INSPECT ABSORBER CONTROL ACTUATOR
  1. Turn the ignition switch off.

  1. Check the front absorber control actuator RH (when DTC C1731/31 is output).

    1. Disconnect the A56 actuator connector.

    2. C179520E03
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (FAR+) - 2 (FAR-)
      Always
      6.4 to 7.2 Ω
      3 (FBR+) - 4 (FBR-)
      Always
      6.4 to 7.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Absorber Control Actuator RH)

  1. Check the front absorber control actuator LH (when DTC C1732/32 is output).

    1. Disconnect the A57 actuator connector.

    2. C179520E05
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (FAL+) - 2 (FAL-)
      Always
      6.4 to 7.2 Ω
      3 (FBL+) - 4 (FBL-)
      Always
      6.4 to 7.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Absorber Control Actuator LH)

  1. Check the rear absorber control actuator RH (when DTC C1733/33 is output).

    1. Disconnect the S1 actuator connector.

    2. C179521E05
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (RAR-) - 2 (RAR+)
      Always
      6.4 to 7.2 Ω
      3 (RBR-) - 4 (RBR+)
      Always
      6.4 to 7.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Absorber Control Actuator RH)

  1. Check the rear absorber control actuator LH (when DTC C1734/34 is output).

    1. Disconnect the S4 actuator connector.

    2. C179521E06
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (RAL-) - 2 (RAL+)
      Always
      6.4 to 7.2 Ω
      3 (RBL-) - 4 (RBL+)
      Always
      6.4 to 7.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Absorber Control Actuator LH)
      Result 
      Result
      Proceed to
      OK
      A
      NG (Front absorber control actuator RH)
      B
      NG (Front absorber control actuator LH)
      C
      NG (Rear absorber control actuator RH)
      D
      NG (Rear absorber control actuator LH)
      E



B
REPLACE FRONT ABSORBER CONTROL ACTUATOR RH (Click here)

C
REPLACE FRONT ABSORBER CONTROL ACTUATOR LH (Click here)

D
REPLACE REAR SHOCK ABSORBER ASSEMBLY RH (Click here)

E
REPLACE REAR SHOCK ABSORBER ASSEMBLY LH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (ABSORBER CONTROL ACTUATOR - SUSPENSION CONTROL ECU)
  1. Check the front side absorber control actuator.

    1. Disconnect the A56 and/or A57 front absorber control actuator connector.

    2. Disconnect the A14 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for Front RH (for DTC C1731/31) 
      Tester Connection
      Condition
      Specified Condition
      A56-1 (FAR+) - A14-7 (FAR+)
      Always
      Below 1 Ω
      A56-2 (FAR-) - A14-8 (FAR-)
      Always
      Below 1 Ω
      A56-3 (FBR+) - A14-1 (FBR+)
      Always
      Below 1 Ω
      A56-4 (FBR-) - A14-2 (FBR-)
      Always
      Below 1 Ω
      A56-1 (FAR+) - Body ground
      Always
      10 kΩ or higher
      A56-2 (FAR-) - Body ground
      Always
      10 kΩ or higher
      A56-3 (FBR+) - Body ground
      Always
      10 kΩ or higher
      A56-4 (FBR-) - Body ground
      Always
      10 kΩ or higher
      for Front LH (for DTC C1732/32) 
      Tester Connection
      Condition
      Specified Condition
      A57-1 (FAL+) - A14-3 (FAL+)
      Always
      Below 1 Ω
      A57-2 (FAL-) - A14-5 (FAL-)
      Always
      Below 1 Ω
      A57-3 (FBL+) - A14-6 (FBL+)
      Always
      Below 1 Ω
      A57-4 (FBL-) - A14-4 (FBL-)
      Always
      Below 1 Ω
      A57-1 (FAL+) - Body ground
      Always
      10 kΩ or higher
      A57-2 (FAL-) - Body ground
      Always
      10 kΩ or higher
      A57-3 (FBL+) - Body ground
      Always
      10 kΩ or higher
      A57-4 (FBL-) - Body ground
      Always
      10 kΩ or higher

  1. Check the rear side absorber control actuator.

    1. Disconnect the S1 and/or S4 rear absorber control actuator connector.

    2. Disconnect the R19 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for Rear RH (for DTC C1733/33) 
      Tester Connection
      Condition
      Specified Condition
      S1-1 (RAR-) - R19-2 (RAR-)
      Always
      Below 1 Ω
      S1-2 (RAR+) - R19-1 (RAR+)
      Always
      Below 1 Ω
      S1-3 (RBR-) - R19-4 (RBR-)
      Always
      Below 1 Ω
      S1-4 (RBR+) - R19-3 (RBR+)
      Always
      Below 1 Ω
      S1-1 (RAR-) - Body ground
      Always
      10 kΩ or higher
      S1-2 (RAR+) - Body ground
      Always
      10 kΩ or higher
      S1-3 (RBR-) - Body ground
      Always
      10 kΩ or higher
      S1-4 (RBR+) - Body ground
      Always
      10 kΩ or higher
      for Rear LH (for DTC C1734/34) 
      Tester Connection
      Condition
      Specified Condition
      S4-1 (RAL-) - R19-6 (RAL-)
      Always
      Below 1 Ω
      S4-2 (RAL+) - R19-5 (RAL+)
      Always
      Below 1 Ω
      S4-3 (RBL-) - R19-8 (RBL-)
      Always
      Below 1 Ω
      S4-4 (RBL+) - R19-7 (RBL+)
      Always
      Below 1 Ω
      S4-1 (RAL-) - Body ground
      Always
      10 kΩ or higher
      S4-2 (RAL+) - Body ground
      Always
      10 kΩ or higher
      S4-3 (RBL-) - Body ground
      Always
      10 kΩ or higher
      S4-4 (RBL+) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1731/31 FR Damping Force Control Actuator Circuit (+ C1732/32, C1733/33, C1734/34) (Aug 2013 – Jul 2014)C1745/45 Exhaust Solenoid (Aug 2013 – Jul 2014) →