2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B2786 No Response from Steering Lock ECU

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU and steering lock actuator assembly (steering lock ECU) stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2786
LIN communication between the certification ECU and steering lock ECU stops for 10 seconds or more.
  1. Steering lock actuator assembly (steering lock ECU)
  2. Certification ECU
  3. Harness or connector

WIRING DIAGRAM

C217632E33

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the steering lock ECU and certification ECU stops, DTC B2785 is also stored.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2786 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
  1. Disconnect the G38 certification ECU connector.

  1. Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G38-29 (LIN) - G35-5 (LIN)
    Always
    Below 1 Ω
    G38-29 (LIN) or G35-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY AND BODY GROUND)

  1. C216966E05
    Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G35-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G35-6 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V
    G35-7 (B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Steering Lock Actuator [Steering Lock ECU])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
  1. Temporarily replace the steering lock actuator assembly (steering lock ECU) with a new one.

    1. for Manual Tilt and Manual Telescopic Steering Column: Click here
    2. for Power Tilt and Power Telescopic Steering Column: Click here


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2786 is not output.



NG
REPLACE CERTIFICATION ECU
OK

END (STEERING LOCK ECU IS DEFECTIVE)


← B2786 No Response from Steering Lock ECU (Aug 2013 – Jul 2014)B2789 No Response from ID BOX (Aug 2013 – Jul 2014) →