2013-2015 Land Cruiser Prado · Service Manual Brake

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.

NOTICE:
Make sure to release the vacuum from the brake booster before removing the master cylinder from the brake booster.


1. DRAIN BRAKE FLUID

NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.


2. REMOVE AIR CLEANER CASE (for 2TR-FE RHD)
  1. Remove the air cleaner case (Click here).


3. REMOVE AIR CLEANER CASE ASSEMBLY (for 5L-E RHD)
  1. Remove the air cleaner case assembly (Click here).


4. REMOVE BRAKE ACTUATOR ASSEMBLY (for RHD)
  1. Remove the brake actuator assembly (Click here).


5. DISCONNECT CLUTCH TUBE (for Manual Transmission)

  1. C215285
    Slide the clip and disconnect the clutch tube.


6. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

  1. for LHD:

    1. C215272
      Disconnect the connector.

    2. Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

    3. C215274
      Remove the 2 nuts and brake master cylinder sub-assembly.

      NOTICE:
      1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
      2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
      3. When installing the master cylinder to the brake booster or removing the master cylinder from the brake booster, make sure that the master cylinder is kept horizontal or with its tip facing downward (the piston faces upward) to prevent the master cylinder piston from falling out.
      4. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a piece of cloth, and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the piston.
      5. Do not use any other type of grease or fluid.
      6. Be careful not to damage the brake tubes.

    4. Remove the O-ring from the brake master cylinder sub-assembly.

  1. for RHD:

    1. C215273
      Disconnect the connector.

    2. C215925
      Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

    3. C213478
      Remove the 2 nuts.

    4. Remove the clamp and brake master cylinder from the brake booster.

    5. Remove the brake master cylinder sub-assembly.

      NOTICE:
      1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
      2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
      3. When installing the master cylinder to the brake booster or removing the master cylinder from the brake booster, make sure that the master cylinder is kept horizontal or with its tip facing downward (the piston faces upward) to prevent the master cylinder piston from falling out.
      4. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a piece of cloth, and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the piston.
      5. Do not use any other type of grease or fluid.
      6. Be careful not to damage the brake tubes.

    6. Remove the O-ring from the brake master cylinder sub-assembly.

← REMOVAL (Aug 2013 – Jul 2014)DISASSEMBLY (from Aug 2013) →