2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Back Door Courtesy Switch Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU receives a door open/closed signal from each door courtesy light switch.

WIRING DIAGRAM

E188450E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH)
  1. Using the intelligent tester, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Courtesy SW
    Back door courtesy switch signal / ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    Glass Hatch Courtesy Switch*
    Glass hatch courtesy switch signal / ON or OFF
    ON: Glass hatch open
    OFF: Glass hatch closed
    -
    1. *: w/ Glass Hatch Opener System

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Back door courtesy light switch does not operate)
    B
    NG (Glass hatch courtesy light switch does not operate)
    C



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT BACK DOOR COURTESY LIGHT SWITCH ASSEMBLY

  1. E139234
    Remove the back door courtesy light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher



NG
REPLACE BACK DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR COURTESY LIGHT SWITCH ASSEMBLY)
  1. Disconnect the G64 main body ECU connector.

  1. Disconnect the R9 back door courtesy light switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G64-19 (BCTY) - R9-1
    Always
    Below 1 Ω
    G64-19 (BCTY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

4. INSPECT BACK WINDOW LOCK ASSEMBLY (GLASS HATCH COURTESY LIGHT SWITCH)

  1. Remove the back window lock (Click here).B241626E02

    Text in Illustration 
    V100135
    Open
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-) - 2 (+)
    Open
    Below 1 Ω
    Closed
    10 kΩ or higher



NG
REPLACE BACK WINDOW LOCK ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK WINDOW LOCK ASSEMBLY AND BODY GROUND)
  1. Disconnect the G64 main body ECU connector.

  1. Disconnect the X4 back window lock connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G64-1 (GCTY) - X4-2 (+)
    Always
    Below 1 Ω
    G64-1 (GCTY) - Body ground
    Always
    10 kΩ or higher
    X4-1 (-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Door Courtesy Switch Circuit (from Aug 2014)Back Door Courtesy Switch Circuit (from Aug 2014) →