2013-2015 Land Cruiser Prado · Service Manual Brake

C1407 Open or Short in Rear Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1407
C1408
Either condition is met:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Rear speed sensor RH/LH
  2. Rear skid control sensor wire
  3. Speed sensor circuit
  4. Master cylinder solenoid (Skid control ECU)

HINT:
  1. DTC C1407 is for the rear speed sensor RH.
  2. DTC C1408 is for the rear speed sensor LH.


WIRING DIAGRAM

C217557E03

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Check the speed sensor signal after replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Rear speed sensor RH open detection/ Error or Normal
    Normal
    -
    RL Speed Open
    Rear speed sensor LH open detection/ Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. INSPECT SKID CONTROL SENSOR WIRE
C214499E04
Text in Illustration 
*A
for RH
*B
for LH
*1
Skid Control Sensor Wire
-
-
  1. Remove the skid control sensor wire (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    Sq1-4 - q1-2 (RR+)
    Always
    Below 1 Ω
    Sq1-3 - q1-1 (RR-)
    Always
    Below 1 Ω
    Sq1-4 - Sq1-3
    Always
    10 kΩ or higher
    Sq1-4 - Sq1-1
    Always
    10 kΩ or higher
    Sq1-4 - Sq1-2
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    Sq1-2 - q2-2 (RL+)
    Always
    Below 1 Ω
    Sq1-1 - q2-1 (RL-)
    Always
    Below 1 Ω
    Sq1-2 - Sq1-1
    Always
    10 kΩ or higher
    Sq1-2 - Sq1-3
    Always
    10 kΩ or higher
    Sq1-2 - Sq1-4
    Always
    10 kΩ or higher



NG
REPLACE SKID CONTROL SENSOR WIRE (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Install the skid control sensor wire.

  1. Disconnect the A7 skid control ECU connector.

  1. Disconnect the q1 and/or q2 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A7-5 (RR+) - q1-2 (RR+)
    Always
    Below 1 Ω
    A7-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    A7-19 (RR-) - q1-1 (RR-)
    Always
    Below 1 Ω
    A7-19 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A7-20 (RL+) - q2-2 (RL+)
    Always
    Below 1 Ω
    A7-20 (RL+) - Body ground
    Always
    10 kΩ or higher
    A7-6 (RL-) - q2-1 (RL-)
    Always
    Below 1 Ω
    A7-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK TERMINAL VOLTAGE (RR+, RL+)
  1. Disconnect the q1 and/or q2 speed sensor connector.

  1. Connect the A7 skid control ECU connector.

  1. C207217E08
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    q1-2 (RR+) - Body ground
    Ignition switch ON
    11 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    q2-2 (RL+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Rear Speed Sensor)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE REAR SPEED SENSOR (Click here)


← C1407 Open or Short in Rear Speed Sensor RH Circuit (+ C1408) (Aug 2013 – Jul 2014)C1409 Front Speed Sensor RH Performance (+ C1410) (Aug 2013 – Jul 2014) →