2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY
  1. Install the rear blower with fan motor with the 3 screws.


2. INSTALL HEATER BRACKET
  1. Install the bracket with the 3 screws and attach the clamp.

  1. Connect the 2 connectors


3. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. w/o Rear No. 2 Seat:

    1. Connect each connector.

    2. Pass the rear seatback lock control lever base through the deck trim side panel.

    3. Attach the 5 clips and 8 claws to install the deck trim side panel.

    4. Install the 4 bolts and screw.

    5. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.

    6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear No. 2 Seat:

    1. Connect each connector.

    2. Attach the 4 clips and 8 claws to install the deck trim side panel.

    3. Install the 2 bolts and screw.

    4. Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }


5. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the other assist grip.

  1. Install the assist grip with the 2 bolts.


6. INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for all assist grip plugs.

  1. Attach the 2 claws to install the assist grip plug.


7. INSTALL FRONT DECK SIDE TRIM COVER RH (w/ Tonneau Cover)

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Attach the 2 claws to install the front deck side trim cover


8. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

HINT:
Use the same procedure for the other No. 1 tonneau cover holder cap.

  1. Attach the 2 claws to install the No. 1 tonneau cover holder cap.


9. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Install the No. 1 luggage compartment trim hook by turning it clockwise.


10. INSTALL REAR NO. 1 LAP BELT OUTER ANCHOR COVER SEAT

HINT:
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

  1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.


11. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

  1. Attach the 4 claws to install the rear floor carpet.

    B238751E01

    Text in Illustration 
    *A
    w/o Deck Rail
    *B
    w/ Deck Rail
    *C
    for Face to Face Seat Type
    -
    -


12. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:
Use the same procedure described for the LH side.


13. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)
  1. Install the floor side rail with the 3 bolts.


14. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
  1. Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.


15. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)
  1. Attach the clip to install the No. 1 deck board.


16. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

B238749E01

HINT:
Use the same procedure for the other front luggage compartment trim cover.

  1. Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.

    Text in Illustration 
    *1
    Luggage Hold Belt Striker

  1. Attach the 4 claws to install the cap.


17. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover.


18. INSTALL OUTER LAP BELT ANCHOR COVER

HINT:
Use the same procedure for the other outer lap belt anchor cover.

  1. Attach the 3 claws to install the outer lap belt anchor cover


19. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.


20. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.


21. INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure described for the LH side.


22. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Install the rear No. 1 seatback assembly (Click here).

  1. for 60/40 Split Double-folding Seat Type RH Side:
    Install the rear No. 1 seatback assembly (Click here).


23. INSTALL REAR NO. 1 SEATBACK ASSEMBLY
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Install the rear No. 1 seatback assembly (Click here).

  1. for 60/40 Split Double-folding Seat Type RH Side:
    Install the rear No. 1 seatback assembly (Click here).


24. INSTALL REAR NO. 2 SEAT ASSEMBLY
  1. for Manual Seat:
    Install the rear No. 2 seat assembly (Click here).

  1. for Power Seat:
    Install the rear No. 2 seat assembly (Click here).

  1. for Face to Face Seat Type:
    Install the rear No. 2 seat assembly (Click here).


25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →