2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B14A2 Driver Side Solar Sensor Short Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

E132508E01
The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the automatic light control sensor (solar sensor) varies according to the amount of sunlight. When the amount of sunlight increases, the output current increases. As the amount of sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects the output current from the automatic light control sensor (solar sensor).
DTC Code
DTC Detection Condition
Trouble Area
B14A2
An open or short in the driver side solar sensor circuit.
  1. Automatic light control sensor (solar sensor)
  2. Harness or connector
  3. Main body ECU (multiplex network body ECU)
  4. Air conditioning amplifier assembly

WIRING DIAGRAM

E196914E15

INSPECTION PROCEDURE

HINT:
  1. If DTC B1244 is output together with other DTCs, troubleshoot DTC B1244 first (Click here).
  2. If the check is performed in a dark place, DTC B14A2 or B14A3 (solar sensor circuit abnormal) may be stored even though the system is normal.


1. READ VALUE USING INTELLIGENT TESTER (SOLAR SENSOR)
  1. Use the Data List to check if the automatic light control sensor (solar sensor) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (D side)
    Automatic light control sensor (solar sensor) / Min.: 0, Max.: 255
    Driver side solar sensor voltage increases as brightness increases
    Open in the circuit: 0.
    Short in the circuit: 255.

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

  1. E152686E64
    Disconnect the H19 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CLTB) - H19-3 (CLTE)
    Ignition switch off
    Below 1 V
    H19-6 (CLTB) - H19-3 (CLTE)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Automatic Light Control Sensor [Solar Sensor])



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the H19 sensor connector.

  1. Disconnect the G25 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    H19-1 (TSL) - G25-33 (TSD)
    Always
    Below 1 Ω
    H19-1 (TSL) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    H19-2 (TSR) - G25-33 (TSD)
    Always
    Below 1 Ω
    H19-2 (TSR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)
  1. *1: for LHD
  2. *2: for RHD

  1. E161710E51
    Remove the automatic light control sensor (solar sensor) with its connector still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    H19-1 (TSL) - H19-3 (CLTE)
    Ignition switch ON
    Sensor subjected to electric light
    0.8 to 4.3 V
    H19-1 (TSL) - H19-3 (CLTE)
    Ignition switch ON
    Sensor covered with cloth
    Below 0.8 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    H19-2 (TSR) - H19-3 (CLTE)
    Ignition switch ON
    Sensor subjected to electric light
    0.8 to 4.3 V
    H19-2 (TSR) - H19-3 (CLTE)
    Ignition switch ON
    Sensor covered with cloth
    Below 0.8 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (Automatic Light Control Sensor [Solar Sensor])

    NOTICE:
    The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 1*1 or 2*2 and the positive (+) lead to terminal 3 of the solar sensor.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
    2. As the inspection light is moved away from the sensor, the voltage decreases.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR) (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)
  1. Disconnect the G64 ECU connector.

  1. Disconnect the H19 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G64-22 (CLTE) - H19-3 (CLTE)
    Always
    Below 1 Ω
    G64-20 (CLTB) - H19-6 (CLTB)
    Always
    Below 1 Ω
    G64-22 (CLTE) - Body ground
    Always
    10 kΩ or higher
    G64-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← B14A2 Driver Side Solar Sensor Short Circuit (Aug 2013 – Jul 2014)B14A3 Front Passenger Side Solar Sensor Short Circuit (Aug 2013 – Jul 2014) →