2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2650 Slide Sensor Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the front power seat switch does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
B2650
The forward and backward lock detection position of the sensor is the same.
  1. Front power seat switch
  2. Separate type front seat cushion spring assembly (Slide motor)
  3. Harness or connector

WIRING DIAGRAM

B238655E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (Click here).

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Slide Operation
    Seat sliding operation
    Front / OFF / Rear
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2. CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT)

  1. B238255E01
    Disconnect the b1*1 or a1*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b1-2 (O/P) - b1-3 (GND)
    Sliding switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a1-2 (O/P) - a1-3 (GND)
    Sliding switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Slide Motor])



NG
Go to step 4
OK


3. CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)

  1. B238515E01
    Connect the b1*1 or a1*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b1-2 (O/P) - Body ground
    Sliding switch on
    4.5 to 4.8 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a1-2 (O/P) - Body ground
    Sliding switch on
    4.5 to 4.8 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (Separate Type Front Seat Cushion Spring Assembly [Slide Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b1*1 or a1*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-5 (SSRS) - b1-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - b1-3 (GND)
    Always
    Below 1 Ω
    b5-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-5 (SSRS) - a1-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - a1-3 (GND)
    Always
    Below 1 Ω
    a5-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

5. INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)

  1. B238714E01
    Remove the separate type front seat cushion spring assembly (slide motor) (Click here).

  1. Check if the seat cushion spring moves smoothly when the battery is connected to the slide motor connector terminals.

    OK:
    for LHD 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 4 (FWD)
    Battery negative (-) → 1 (BACK)
    Seat cushion spring moves forward
    Battery positive (+) → 1 (BACK)
    Battery negative (-) → 4 (FWD)
    Seat cushion spring moves backward
    for RHD 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1 (FWD)
    Battery negative (-) → 4 (BACK)
    Seat cushion spring moves forward
    Battery positive (+) → 4 (BACK)
    Battery negative (-) → 1 (FWD)
    Seat cushion spring moves backward

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b4*1 or a4*2 switch connector.

  1. Disconnect the b1*1 or a1*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b4-3 (SLD+) - b1-4 (FWD)
    Always
    Below 1 Ω
    b4-4 (SLD-) - b1-1 (BACK)
    Always
    Below 1 Ω
    b4-3 (SLD+) - Body ground
    Always
    10 kΩ or higher
    b4-4 (SLD-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a4-3 (SLD+) - a1-1 (FWD)
    Always
    Below 1 Ω
    a4-4 (SLD-) - a1-4 (BACK)
    Always
    Below 1 Ω
    a4-3 (SLD+) - Body ground
    Always
    10 kΩ or higher
    a4-4 (SLD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)


← B2650 Slide Sensor Malfunction (Aug 2013 – Jul 2014)B2651 Reclining Sensor Malfunction (Aug 2013 – Jul 2014) →