B2651 Reclining Sensor Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the front power seat switch does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2651 |
The forward and backward lock detection position of the sensor is the same. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION) |
Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (Click here).
Driver Seat Tester Display
Test Part
Control Ranger
Diagnostic Note
Seat Reclining
Seat reclining operation
Front / OFF / Rear
-
- OK:
- Motor operates normally.
|
|
||||
| OK | |
| 2. CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT) |
Disconnect the f1*1 or e1*2 motor connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Switch Condition
Specified Condition
f1-2 (O/P) - f1-3 (GND)
Reclining switch on
4.8 to 5.1 V
for RHD Tester Connection
Switch Condition
Specified Condition
e1-2 (O/P) - e1-3 (GND)
Reclining switch on
4.8 to 5.1 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Separate Type Front Seatback Assembly [Reclining Motor])
|
|
||||
| OK | |
| 3. CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR) |
Connect the f1*1 or e1*2 motor connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Switch Condition
Specified Condition
f1-2 (O/P) - Body ground
Reclining switch on
4.5 to 4.8 V
for RHD Tester Connection
Switch Condition
Specified Condition
e1-2 (O/P) - Body ground
Reclining switch on
4.5 to 4.8 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Component with harness connected
(Separate Type Front Seatback Assembly [Reclining Motor])
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the b5*1 or a5*2 switch connector.
Disconnect the f1*1 or e1*2 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
b5-11 (SSRR) - f1-2 (O/P)
Always
Below 1 Ω
b5-1 (SGND) - f1-3 (GND)
Always
Below 1 Ω
b5-11 (SSRR) - Body ground
Always
10 kΩ or higher
b5-1 (SGND) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
a5-11 (SSRR) - e1-2 (O/P)
Always
Below 1 Ω
a5-1 (SGND) - e1-3 (GND)
Always
Below 1 Ω
a5-11 (SSRR) - Body ground
Always
10 kΩ or higher
a5-1 (SGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. INSPECT SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR) |
Remove the separate type front seatback assembly (reclining motor) (Click here).

Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.
- OK:
Measurement Condition
Operational Direction
Battery positive (+) → 1 (FWD)
Battery negative (-) → 4 (BACK)
Seatback moves forward
Battery positive (+) → 4 (BACK)
Battery negative (-) → 1 (FWD)
Seatback moves backward
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the b4*1 or a4*2 switch connector.
Disconnect the f1*1 or e1*2 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
b4-9 (RCL+) - f1-1 (FWD)
Always
Below 1 Ω
b4-11 (RCL-) - f1-4 (BACK)
Always
Below 1 Ω
b4-9 (RCL+) - Body ground
Always
10 kΩ or higher
b4-11 (RCL-) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
a4-9 (RCL+) - e1-4 (FWD)
Always
Below 1 Ω
a4-11 (RCL-) - e1-5 (BACK)
Always
Below 1 Ω
a4-9 (RCL+) - Body ground
Always
10 kΩ or higher
a4-11 (RCL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
