2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2652 Front Vertical Sensor Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the front power seat switch does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
B2652
The upward and downward lock detection position is of the sensor the same.
  1. Front power seat switch
  2. Separate type front seat cushion assembly (Front vertical motor)
  3. Harness or connector

WIRING DIAGRAM

B238655E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the intelligent test to generate a control command, and then check the power seat motor function (Click here).

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Vertical Operation
    Seat front vertical operation
    Up / OFF / Down
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2. CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT)

  1. B238255E03
    Disconnect the b2*1 or a2*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b2-2 (O/P) - b2-3 (GND)
    Front vertical switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a2-2 (O/P) - a2-3 (GND)
    Front vertical switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])



NG
Go to step 4
OK


3. CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)

  1. B238515E03
    Connect the b2*1 or a2*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b2-2 (O/P) - Body ground
    Front vertical switch on
    4.5 to 4.8 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a2-2 (O/P) - Body ground
    Front vertical switch on
    4.5 to 4.8 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b2*1 or a2*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-3 (SSFV) - b2-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - b2-3 (GND)
    Always
    Below 1 Ω
    b5-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-3 (SSFV) - a2-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - a2-3 (GND)
    Always
    Below 1 Ω
    a5-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

5. INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)

  1. B238256E02
    Remove the separate type front seat cushion spring assembly (front vertical motor) (Click here).

  1. Check if the seat cushion spring moves smoothly when the battery is connected to the front vertical motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → 4 (UP)
    Battery negative (-) → 1 (DOWN)
    Seat cushion spring moves upward
    Battery positive (+) → 1 (DOWN)
    Battery negative (-) → 4 (UP)
    Seat cushion spring moves downward



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b4*1 or a4*2 switch connector.

  1. Disconnect the b2*1 or a2*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b4-8 (FRV+) - b2-4 (UP)
    Always
    Below 1 Ω
    b4-5 (FRV-) - b2-1 (DOWN)
    Always
    Below 1 Ω
    b4-8 (FRV+) - Body ground
    Always
    10 kΩ or higher
    b4-5 (FRV-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a4-8 (FRV+) - a2-4 (UP)
    Always
    Below 1 Ω
    a4-5 (FRV-) - a2-1 (DOWN)
    Always
    Below 1 Ω
    a4-8 (FRV+) - Body ground
    Always
    10 kΩ or higher
    a4-5 (FRV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)


← B2651 Reclining Sensor Malfunction (from Aug 2014)B2652 Front Vertical Sensor Malfunction (from Aug 2014) →