2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2651 Reclining Sensor Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the front power seat switch does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
B2651
The forward and backward lock detection position of the sensor is the same.
  1. Front power seat switch
  2. Separate type front seatback assembly (Reclining motor)
  3. Harness or connector

WIRING DIAGRAM

B238655E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (Click here).

    Driver Seat 
    Tester Display
    Test Part
    Control Ranger
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front / OFF / Rear
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2. CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT)

  1. B238255E02
    Disconnect the f1*1 or e1*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    f1-2 (O/P) - f1-3 (GND)
    Reclining switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    e1-2 (O/P) - e1-3 (GND)
    Reclining switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seatback Assembly [Reclining Motor])



NG
Go to step 4
OK


3. CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)

  1. B238515E02
    Connect the f1*1 or e1*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    f1-2 (O/P) - Body ground
    Reclining switch on
    4.5 to 4.8 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    e1-2 (O/P) - Body ground
    Reclining switch on
    4.5 to 4.8 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (Separate Type Front Seatback Assembly [Reclining Motor])



NG
REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the f1*1 or e1*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-11 (SSRR) - f1-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - f1-3 (GND)
    Always
    Below 1 Ω
    b5-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-11 (SSRR) - e1-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - e1-3 (GND)
    Always
    Below 1 Ω
    a5-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

5. INSPECT SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)

  1. B238256E01
    Remove the separate type front seatback assembly (reclining motor) (Click here).

  1. Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → 1 (FWD)
    Battery negative (-) → 4 (BACK)
    Seatback moves forward
    Battery positive (+) → 4 (BACK)
    Battery negative (-) → 1 (FWD)
    Seatback moves backward



NG
REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b4*1 or a4*2 switch connector.

  1. Disconnect the f1*1 or e1*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b4-9 (RCL+) - f1-1 (FWD)
    Always
    Below 1 Ω
    b4-11 (RCL-) - f1-4 (BACK)
    Always
    Below 1 Ω
    b4-9 (RCL+) - Body ground
    Always
    10 kΩ or higher
    b4-11 (RCL-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a4-9 (RCL+) - e1-4 (FWD)
    Always
    Below 1 Ω
    a4-11 (RCL-) - e1-5 (BACK)
    Always
    Below 1 Ω
    a4-9 (RCL+) - Body ground
    Always
    10 kΩ or higher
    a4-11 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)


← B2651 Reclining Sensor Malfunction (Aug 2013 – Jul 2014)B2652 Front Vertical Sensor Malfunction (Aug 2013 – Jul 2014) →