2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2653 Lifter Sensor Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the front power seat switch does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
B2653
The upward and downward lock detection position of the sensor is the same.
  1. Front power seat switch
  2. Separate type front seat cushion spring assembly (Lifter motor)
  3. Harness or connector

WIRING DIAGRAM

B238655E04

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (Click here).

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Lifter Operation
    Seat lifter operation
    Up / OFF / Down
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2. CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT)

  1. B238255E04
    Disconnect the b3*1 or a3*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b3-2 (O/P) - b3-3 (GND)
    Lifter switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a3-2 (O/P) - a3-3 (GND)
    Lifter switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])



NG
Go to step 4
OK


3. CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR)

  1. B238515E04
    Connect the b3*1 or a3*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b3-2 (O/P) - Body ground
    Lifter switch on
    4.5 to 4.8 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a3-2 (O/P) - Body ground
    Lifter switch on
    4.5 to 4.8 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component with harness connected
    (Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b3*1 or a3*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-4 (SSRL) - b3-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - b3-3 (GND)
    Always
    Below 1 Ω
    b5-4 (SSRL) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-4 (SSRL) - a3-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - a3-3 (GND)
    Always
    Below 1 Ω
    a5-4 (SSRL) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)

5. INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR)

  1. B238256E03
    Remove the separate type front seat cushion spring assembly (lifter motor) (Click here).

  1. Check if the seat cushion spring moves smoothly when the battery is connected to the lifter motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → 1 (UP)
    Battery negative (-) → 4 (DOWN)
    Seat cushion spring moves upward
    Battery positive (+) → 4 (DOWN)
    Battery negative (-) → 1 (UP)
    Seat cushion spring moves downward



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (LIFTER MOTOR) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b4*1 or a4*2 switch connector.

  1. Disconnect the b3*1 or a3*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b4-10 (LFT+) - b3-1 (UP)
    Always
    Below 1 Ω
    b4-12 (LFT-) - b3-4 (DOWN)
    Always
    Below 1 Ω
    b4-10 (LFT+) - Body ground
    Always
    10 kΩ or higher
    b4-12 (LFT-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a4-10 (LFT+) - a3-1 (UP)
    Always
    Below 1 Ω
    a4-12 (LFT-) - a3-4 (DOWN)
    Always
    Below 1 Ω
    a4-10 (LFT+) - Body ground
    Always
    10 kΩ or higher
    a4-12 (LFT-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH (Click here)


← B2653 Lifter Sensor Malfunction (Aug 2013 – Jul 2014)B2658 Short in Sensor with Motor Power Supply Circuit (Aug 2013 – Jul 2014) →