2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Power Source Mode does not Change to ON (IG and ACC)

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the engine switch is pushed with the key in the cabin, the power management control ECU receives signals to switch the power source mode.

WIRING DIAGRAM

C217209E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

  1. A207890E06
    Disconnect the G51 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G51-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    G51-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the G51 power management control ECU connector.

  1. A207890E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-6 (GND) - Body ground
    Always
    Below 1 Ω
    G51-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. READ VALUE USING INTELLIGENT TESTER (KEY CERTIFI WAIT T-OUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester on.

    HINT:
    When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List and check that "No" is displayed 1 second after turning the engine switch from off to on (IG).

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Certifi Wait T-Out
    Key certification waiting timed out / Yes or No
    Yes: Key certification waiting timed out
    No: Key certification completed within specified time
    -

    OK:
    "No" is displayed 1 second after turning the engine switch from off to on (IG).



NG
Go to step 9
OK


4. READ VALUE USING INTELLIGENT TESTER (START SWITCH 1, 2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch1
    Start Switch 1 / ON or OFF
    ON: Engine switch pushed
    OFF: Engine switch not pushed
    -
    Start Switch2
    Start Switch 2 / ON or OFF
    ON: Engine switch pushed
    OFF: Engine switch not pushed
    -

    OK:
    The display changes in response to the operation of the engine switch.



NG
Go to step 7
OK


5. CHECK POWER MANAGEMENT CONTROL ECU
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List and check that the display changes according to the changes in the power source mode when the engine switch is pushed.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power Supply Condition / IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    IG2 ON: IG2 relay on
    ST ON: ST request signal on
    All OFF: All relays off
    IG1 ON: IG1 relay on
    ACC ON: ACC relay on
    -

    OK:
    Display changes according to the changes in the power source mode when the engine switch is pushed.

  1. Measure the voltage according to the value(s) in the table below.C182533E19

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-20 (IG1D) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    G50-8 (IG2D) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    G51-19 (ACCD) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


6. CONFIRMATION TEST
  1. Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.

    OK:
    The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.



NG
CHECK RELAY CONTACT SIDE CIRCUIT
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. INSPECT ENGINE SWITCH

  1. A207999E02
    Remove the engine switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Engine switch not pushed
    10 kΩ or higher
    Engine switch pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Engine switch not pushed
    10 kΩ or higher
    Engine switch pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Engine Switch)

    HINT:
    1. for 1GR-FE (LHD): Click here.
    2. for 1GR-FE (RHD): Click here.
    3. for 2TR-FE: Click here.
    4. for 1KD-FTV (LHD): Click here.
    5. for 1KD-FTV (RHD): Click here.



NG
REPLACE ENGINE SWITCH
OK


8. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE SWITCH)
  1. Disconnect the G51 power management control ECU connector.

  1. Disconnect the G36 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-17 (SSW2) - G36-2 (SS2)
    Always
    Below 1 Ω
    G51-18 (SSW1) - G36-7 (SS1)
    G51-17 (SSW2) - Body ground
    Always
    10 kΩ or higher
    G51-18 (SSW1) - Body ground
    G36-5 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

9. CHECK FOR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source / DTC.

  1. Read the DTCs.

  1. Enter the following menus: Body / Entry&Start / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    None of the following DTCs are output:
    B2785 Communication Malfunction between ECUs Connected by LIN
    B2287 LIN Communication Master Malfunction
    B2784 Antenna Coil Open/Short
    A
    DTC B2287 is output but B2785 is not
    B
    A DTC other than B2287 is output.
    C



B
GO TO DTC (B2287) (Click here)

C
GO TO DTC CHART (Click here)
A

GO TO ENTRY AND START SYSTEM (FOR ENTRY FUNCTION) (Room Oscillator does not Recognize Key) (Click here)


← Power Source Mode does not Change to ON (IG and ACC) (Aug 2013 – Jul 2014)Power Source Mode does not Change to ON (IG) (Aug 2013 – Jul 2014) →