2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U1002 Lost Communication with Gateway Module (Power Management1)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. The power management control ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the V2 bus.
  2. When the power management control ECU receives a response signal from the ECUs connected to the V2 bus, the power management control ECU recognizes and memorizes that the ECU is connected to the V2 bus. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to the V2 bus when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to the V2 bus, the power management control ECU determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U1002
Lost communication with the gateway module (Power Management1).
  1. V2 bus circuit
  2. Parking assist ECU CAN branch wire or connector*1
  3. Clearance warning ECU assembly CAN branch wire or connector*2
  4. Driving support ECU assembly CAN branch wire or connector*3
  5. Stabilizer control ECU CAN branch wire or connector*4
  6. Seat belt control ECU CAN branch wire or connector*3
  7. Blind spot monitor sensor LH CAN branch wire or connector*5
  8. Suspension control ECU CAN branch wire or connector*6
  9. Headlight swivel ECU assembly CAN branch wire or connector*7
  10. Power management control ECU CAN main wire or connector
  11. Parking assist ECU*1
  12. Clearance warning ECU assembly*2
  13. Driving support ECU assembly*3
  14. Stabilizer control ECU*4
  15. Seat belt control ECU*3
  16. Blind spot monitor sensor LH*5
  17. Suspension control ECU*6
  18. Headlight swivel ECU assembly*7
  19. Power management control ECU
  20. No. 1 junction connector
  21. No. 3 junction connector
  22. No. 5 junction connector
  23. No. 6 junction connector*5
  24. No. 7 junction connector
  1. *1: w/ Side Monitor System
  2. *2: w/ TOYOTA Parking Assist-sensor System
  3. *3: w/ Pre-crash Safety System
  4. *4: w/ Kinetic Dynamic Suspension System
  5. *5: w/ Blind Spot Monitor System
  6. *6: w/ Air Suspension System
  7. *7: for LED Headlight

WIRING DIAGRAM

C294683E02
C294684E02

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)

  1. C198954E30
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance: Malfunction
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    54 to 69 Ω
    Higher than 70 Ω: Open in CAN main bus line
    G51-26 (CA2H) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G51-25 (CA2L) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G51-26 (CA2H) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    G51-25 (CA2L) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main bus line
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 19

C
Go to step 67
A


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C220696E84
    Disconnect the G95 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-1 (CANH) - G95-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C220696E85
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-3 (CANH) - G95-14 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 10
OK

REPLACE NO. 3 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

  1. C220696E86
    Disconnect the G98 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-2 (CANH) - G98-13 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 8
OK


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C220696E87
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-1 (CANH) - G98-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 1 JUNCTION CONNECTOR)

  1. C198951E89
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (POWER MANAGEMENT CONTROL ECU - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C220696E88
    Disconnect the A73 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-1 (CANH) - A73-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    Result 
    Result
    Proceed to
    OK (w/ Blind Spot Monitor System)
    A
    OK (w/o Blind Spot Monitor System)
    B
    NG
    C



B
Go to step 16

C
Go to step 17
A


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C220696E75
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-2 (CANH) - A73-13 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 13
OK

REPLACE NO. 5 JUNCTION CONNECTOR

13. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C220696E89
    Disconnect the R47 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    R47-1 (CANH) - R47-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C220696E90
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    R47-3 (CANH) - R47-14 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 6 JUNCTION CONNECTOR

16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C220696E91
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-2 (CANH) - A73-13 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NO. 5 JUNCTION CONNECTOR

17. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C210060E69
    Disconnect the G102 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G102-3 (CANH) - G102-2 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 7 JUNCTION CONNECTOR

19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)

  1. C198954E31
    Disconnect the A73 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    108 to 132 Ω
    G51-26 (CA2H) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-25 (CA2L) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-26 (CA2H) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher
    G51-25 (CA2L) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Blind Spot Monitor System)
    B
    NG (w/o Blind Spot Monitor System)
    C



B
Go to step 29

C
Go to step 44
A


20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)

NOTICE:
For vehicles without an air suspension system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Headlight Swivel ECU Assembly)".

  1. C294690E28
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-3 (CANH) - A73-14 (CANL)
    Engine switch off
    200 Ω or higher
    A73-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A73-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A73-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A73-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 23
OK


21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NOTICE:
For vehicles without a halogen headlight, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Power Management Control ECU)".

  1. C294690E29
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-4 (CANH) - A73-15 (CANL)
    Engine switch off
    200 Ω or higher
    A73-4 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A73-15 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A73-4 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A73-15 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 25
OK


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C294690E30
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-1 (CANH) - A73-12 (CANL)
    Engine switch off
    108 to 132 Ω
    A73-1 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A73-12 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A73-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A73-12 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 27
OK

REPLACE NO. 5 JUNCTION CONNECTOR

23. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


24. CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)

  1. C217406E10
    Disconnect the A49 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A49-7 (CANH) - A49-8 (CANL)
    Engine switch off
    54 to 69 Ω
    A49-7 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A49-8 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A49-7 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A49-8 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Suspension Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)

25. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


26. CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)

  1. C217420E08
    Disconnect the A58 headlight swivel ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A58-12 (CANH) - A58-13 (CANL)
    Engine switch off
    54 to 69 Ω
    A58-12 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A58-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A58-12 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A58-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Swivel ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (CANH, CANL)
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

27. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR)

  1. C210068E17
    Disconnect the G102 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G102-3 (CANH) - G102-2 (CANL)
    Engine switch off
    108 to 132 Ω
    G102-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G102-2 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G102-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G102-2 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 7 JUNCTION CONNECTOR

29. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C294690E31
    Disconnect the R47 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    R47-3 (CANH) - R47-14 (CANL)
    Engine switch off
    108 to 132 Ω
    R47-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    R47-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    R47-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    R47-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

  1. C198954E32
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    108 to 132 Ω
    G51-26 (CA2H) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-25 (CA2L) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-26 (CA2H) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher
    G51-25 (CA2L) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)



NG
Go to step 35
OK


32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)

  1. C294690E22
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    R47-2 (CANH) - R47-13 (CANL)
    Engine switch off
    200 Ω or higher
    R47-2 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    R47-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    R47-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    R47-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 33
OK

REPLACE NO. 6 JUNCTION CONNECTOR

33. CONNECT CONNECTOR
  1. Reconnect the R47 No. 6 junction connector.


NEXT


34. CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)

  1. C268298E11
    Disconnect the R42 blind spot monitor sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    R42-2 (CA1P) - R42-7 (CA1N)
    Engine switch off
    54 to 69 Ω
    R42-2 (CA1P) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    R42-7 (CA1N) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    R42-2 (CA1P) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    R42-7 (CA1N) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor LH)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)
OK

REPLACE BLIND SPOT MONITOR SENSOR LH (Click here)

35. CONNECT CONNECTOR
  1. Reconnect the R47 No. 6 junction connector.


NEXT


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C294690E16
    Disconnect the G95 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-3 (CANH) - G95-14 (CANL)
    Engine switch off
    108 to 132 Ω
    G95-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G95-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

  1. C198954E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    108 to 132 Ω
    G51-26 (CA2H) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-25 (CA2L) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-26 (CA2H) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher
    G51-25 (CA2L) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)



NG
Go to step 53
OK


38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NOTICE:
For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Stabilizer Control ECU)".

  1. C294690E20
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-6 (CANH) - G95-17 (CANL)
    Engine switch off
    200 Ω or higher
    G95-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-17 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G95-17 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 40
OK


39. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)

NOTICE:
For vehicles without a kinetic dynamic suspension system, replace No. 3 junction connector.

  1. C294690E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-5 (CANH) - G95-16 (CANL)
    Engine switch off
    200 Ω or higher
    G95-5 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-16 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-5 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G95-16 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 42
OK

REPLACE NO. 3 JUNCTION CONNECTOR

40. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


41. CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)

  1. C217422E11
    Disconnect the G118 seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G118-1 (CANH) - G118-2 (CANL)
    Engine switch off
    54 to 69 Ω
    G118-1 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G118-2 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G118-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G118-2 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Seat Belt Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)

42. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


43. CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)

  1. C217421E04
    Disconnect the G123 stabilizer control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G123-29 (CANH) - G123-28 (CANL)
    Engine switch off
    54 to 69 Ω
    G123-29 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G123-28 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G123-29 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G123-28 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Stabilizer Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STABILIZER CONTROL ECU (CANH, CANL)
OK

REPLACE STABILIZER CONTROL ECU (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C294690E16
    Disconnect the G95 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-3 (CANH) - G95-14 (CANL)
    Engine switch off
    108 to 132 Ω
    G95-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G95-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


46. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

  1. C198954E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    108 to 132 Ω
    G51-26 (CA2H) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-25 (CA2L) - G51-6 (GND)
    Engine switch off
    200 Ω or higher
    G51-26 (CA2H) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher
    G51-25 (CA2L) - G51-1 (AM22)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)



NG
Go to step 53
OK


47. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NOTICE:
For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Stabilizer Control ECU)".

  1. C294690E20
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-6 (CANH) - G95-17 (CANL)
    Engine switch off
    200 Ω or higher
    G95-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-17 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G95-17 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 49
OK


48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)

NOTICE:
For vehicles without a kinetic dynamic suspension system, replace No. 3 junction connector.

  1. C294690E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-5 (CANH) - G95-16 (CANL)
    Engine switch off
    200 Ω or higher
    G95-5 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-16 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G95-5 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G95-16 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 51
OK

REPLACE NO. 3 JUNCTION CONNECTOR

49. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


50. CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)

  1. C217422E11
    Disconnect the G118 seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G118-1 (CANH) - G118-2 (CANL)
    Engine switch off
    54 to 69 Ω
    G118-1 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G118-2 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G118-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G118-2 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Seat Belt Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)

51. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


52. CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)

  1. C217421E04
    Disconnect the G123 stabilizer control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G123-29 (CANH) - G123-28 (CANL)
    Engine switch off
    54 to 69 Ω
    G123-29 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G123-28 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G123-29 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G123-28 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Stabilizer Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STABILIZER CONTROL ECU (CANH, CANL)
OK

REPLACE STABILIZER CONTROL ECU (Click here)

53. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


54. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C294690E23
    Disconnect the G98 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-1 (CANH) - G98-12 (CANL)
    Engine switch off
    108 to 132 Ω
    G98-1 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-12 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G98-12 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


55. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - PARKING ASSIST ECU)

NOTICE:
For vehicles without a side monitor system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Driving Support ECU Assembly)".

  1. C294690E24
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-3 (CANH) - G98-14 (CANL)
    Engine switch off
    200 Ω or higher
    G98-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G98-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 59
OK


56. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

NOTICE:
For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Clearance Warning ECU Assembly)".

  1. C294690E25
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-4 (CANH) - G98-15 (CANL)
    Engine switch off
    200 Ω or higher
    G98-4 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-15 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-4 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G98-15 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 61
OK


57. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

NOTICE:
For vehicles without a TOYOTA parking assist-sensor system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Power Management Control ECU)".

  1. C294690E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-5 (CANH) - G98-16 (CANL)
    Engine switch off
    200 Ω or higher
    G98-5 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-16 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-5 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G98-16 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 63
OK


58. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

  1. C294690E27
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-2 (CANH) - G98-13 (CANL)
    Engine switch off
    108 to 132 Ω
    G98-2 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G98-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G98-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 65
OK

REPLACE NO. 1 JUNCTION CONNECTOR

59. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


60. CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)

  1. C217423E14
    Disconnect the I7 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I7-40 (CANH) - I7-39 (CANL)
    Engine switch off
    54 to 69 Ω
    I7-40 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    I7-39 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    I7-40 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    I7-39 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Parking Assist ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING ASSIST ECU (CANH, CANL)
OK

REPLACE PARKING ASSIST ECU (Click here)

61. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


62. CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)

  1. C217423E15
    Disconnect the G119 driving support ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G119-39 (CA2H) - G119-17 (CA2L)
    Engine switch off
    54 to 69 Ω
    G119-39 (CA2H) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G119-17 (CA2L) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G119-39 (CA2H) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G119-17 (CA2L) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Driving Support ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT ECU ASSEMBLY (CA2H, CA2L)
OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY (Click here)

63. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


64. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

  1. C266899E08
    Disconnect the I1*1 or G154*2 clearance warning ECU assembly connector.
    1. *1: for 4 Sensor Type
    2. *2: for 8 Sensor Type

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 4 Sensor Type 
    Tester Connection
    Switch Condition
    Specified Condition
    I1-3 (R1) - I1-5 (R2)
    Engine switch off
    54 to 69 Ω
    I1-3 (R1) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    I1-5 (R2) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    I1-3 (R1) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    I1-5 (R2) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    for 8 Sensor Type 
    Tester Connection
    Switch Condition
    Specified Condition
    G154-3 (R1) - G154-5 (R2)
    Engine switch off
    54 to 69 Ω
    G154-3 (R1) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G154-5 (R2) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G154-3 (R1) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G154-5 (R2) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *A
    for 4 Sensor Type
    *B
    for 8 Sensor Type
    *a
    Front view of wire harness connector
    (to Clearance Warning ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)

65. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


66. CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)

  1. C206323E29
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    Engine switch off
    108 to 132 Ω
    G51-26 (CA2H) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G51-25 (CA2L) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G51-26 (CA2H) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G51-25 (CA2L) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA2H, CA2L)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

67. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)

  1. C198951E90
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-5 (GND2) - Body ground
    Always
    Below 1 Ω
    G51-6 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G51-1 (AM22) - Body ground
    Always
    11 to 14 V
    G51-2 (AM21) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Power Management Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)


← U0233 Lost Communication with Blind Spot Monitor Master Module (from Aug 2014)U1002 Lost Communication with Gateway Module (Power Management1) (from Aug 2014) →