C1611 ECU Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored if the parking assist ECU judges that there is an internal malfunction as a result of its self check.- HINT:
- The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1611 |
|
|
INSPECTION PROCEDURE
- NOTICE:
- When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).
- When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
| 1. READ VALUE USING GTS (PARKING ASSIST ECU STATUS) |
Use the Data List to check if the parking assist ECU status is functioning properly (Click here).
Parking Assist Monitor System Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
EEPROM Status (Initial read)
Parking assist ECU information / OK or NG
OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
AISIC Output Status
Output condition of camera display signal / OK or NG
OK: Output condition of camera display signal is normal
NG: Output condition of camera display signal is abnormal
If "NG" is displayed, there is a malfunctions in parking assist ECU.
Result Result
Proceed to
OK is displayed for both items.
A
NG is displayed for EEPROM Status (Initial read).
A
NG is displayed for AISIC Output Status
B
|
|
||||
| A | |
| 2. SETTINGS (PARKING ASSIST ECU INITIALIZATION) |
- HINT:
- The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.
- If the parking assist ECU cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.
- The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.
Use the transition of diagnosis screens (note which transition pattern occurs) to confirm if the parking assist ECU was able to properly store the information from initialization (Click here).
- HINT:
- The procedure to make the parking assist ECU store the vehicle information differs when the parking assist ECU has stored the information (initialized) and when the information has not been stored (not initialized).
Perform the following procedure depending on the memory conditions to register the vehicle information into the parking assist ECU.
Condition
Procedure
Not initialized
Parking assist ECU initialization (Click here)
Initialized
- Back camera position setting (Click here)
- Steering angle setting (Click here)
- Side camera position setting (Click here )
- Back camera position setting (Click here)
| NEXT | |
| 3. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC C1611 is not output.
- HINT:
- If DTC C1611 is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.
- If DTC C1611 is still output after performing the procedure to make the parking assist ECU store the vehicle information 3 times, replace the parking assist ECU.
- If DTC C1611 is output frequently, replace the parking assist ECU even though the DTC is not output when rechecking for DTCs.
- If DTC C1611 is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.
| Proceed to |
Result |
| OK |
A |
| NG (for LHD) |
B |
| NG (for RHD) |
C |
|
|
||||
|
|
||||
| A | ||
| ||
