2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Image from Camera for Parking Assist Monitor is Abnormal

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the navigation receiver assembly*1 or radio and display receiver assembly*2 via the parking assist ECU.
  1. *1: for Navigation Receiver Type
  2. *2: for Radio and Display Type

WIRING DIAGRAM

E285881E02

INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" is displayed on the parking assist ECU after the battery terminal has been disconnected, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

HINT:
Images may be unclear even in normal conditions if:
  1. Electrical devices are used in the cabin (noise may occur in the image).
  2. The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
  3. The camera lens is dirty with snow, mud, etc.
  4. A strong beam of light, such as a sunbeam or headlight, hits the camera.
  5. It is too dark around the camera (at night etc.).
  6. The ambient temperature around the camera is either too high or too low.
  7. The vehicle is tilted at a steep angle.
  8. The rear television camera assembly lens is scratched.
  9. The rear television camera assembly lens has drops of water on it or the humidity is high.
  10. When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.


1. CHECK SIDE MONITOR SYSTEM
  1. Check if the same malfunction occurs when the side monitor screen is displayed.

    Result 
    Result
    Proceed to
    Malfunction occurs when parking assist monitor screen is displayed (side monitor screen is normal).
    A
    Malfunction occurs when parking assist monitor screen and side monitor screen are displayed.
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY AND BODY GROUND)
  1. Disconnect the I7 parking assist ECU connector.

  1. Disconnect the X9*1 or v2*2 rear television camera assembly connector.

    1. *1: w/ Tire Carrier
    2. *2: w/o Tire Carrier

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Tire Carrier 
    Tester Connection
    Condition
    Specified Condition
    I7-38 (CV-) - X9-2 (CV-)
    Always
    Below 1 Ω
    I7-15 (CV+) - X9-3 (CV+)
    Always
    Below 1 Ω
    I7-14 (CB+) - X9-6 (CB+)
    Always
    Below 1 Ω
    I7-37 (CGND) - X9-5 (CGND)
    Always
    Below 1 Ω
    I7-38 (CV-) - Body ground
    Always
    10 kΩ or higher
    I7-15 (CV+) - Body ground
    Always
    10 kΩ or higher
    I7-14 (CB+) - Body ground
    Always
    10 kΩ or higher
    I7-37 (CGND) - Body ground
    Always
    10 kΩ or higher
    w/o Tire Carrier 
    Tester Connection
    Condition
    Specified Condition
    I7-38 (CV-) - v2-2 (CV-)
    Always
    Below 1 Ω
    I7-15 (CV+) - v2-3 (CV+)
    Always
    Below 1 Ω
    I7-14 (CB+) - v2-6 (CB+)
    Always
    Below 1 Ω
    I7-37 (CGND) - v2-5 (CGND)
    Always
    Below 1 Ω
    I7-38 (CV-) - Body ground
    Always
    10 kΩ or higher
    I7-15 (CV+) - Body ground
    Always
    10 kΩ or higher
    I7-14 (CB+) - Body ground
    Always
    10 kΩ or higher
    I7-37 (CGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK PARKING ASSIST ECU (CB+, CGND)

  1. E245958E34
    Reconnect the I7 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-37 (CGND) - Body ground
    Always
    Below 1 Ω
    I7-38 (CV-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I7-14 (CB+) - Body ground
    Engine switch on (IG)
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)
Result 
Proceed to
Result
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A


4. CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)
E245725E33
Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)
*b
Waveform A
*c
Waveform B
*d
Synchronized Signal
*e
Video Waveform
-
-
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    1. A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
      1. *1: for Navigation Receiver Type
      2. *2: for Radio and Display Type
    2. The video waveform changes according to the image sent by the rear television camera assembly.

    Item
    Content
    Terminal No. (Symbol)
    I7-15 (CV+) - I7-37 (CGND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    1. Waveform A: Engine switch on (IG), camera lens is not covered, displaying an image
    2. Waveform B: Engine switch on (IG), camera lens is covered, blacking out the screen

    OK:
    Waveform is as shown in the illustration.

Result 
Proceed to
Result
OK
A
NG (w/ Tire Carrier)
B
NG (w/o Tire Carrier)
C


B
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)

C
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
A


5. CHECK HARNESS AND CONNECTOR
  1. Disconnect the I7 parking assist ECU connector.

  1. Disconnect the H50 navigation receiver assembly*1 or radio and display receiver assembly*2 connectors.

    1. *1: for Navigation Receiver Type
    2. *2: for Radio and Display Type

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-16 (NS+) - H50-12 (V+)
    Always
    Below 1 Ω
    I7-17 (NS-) - H50-24 (V-)
    Always
    Below 1 Ω
    I7-18 (NSG) - H50-23 (CGND)
    Always
    Below 1 Ω
    I7-16 (NS+) - Body ground
    Always
    10 kΩ or higher
    I7-17 (NS-) - Body ground
    Always
    10 kΩ or higher
    I7-18 (NSG) - Body ground
    Always
    Below 1 kΩ

Result 
Result
Proceed to
OK (for Navigation Receiver Type)
A
OK (for Radio and Display Type)
B
NG
C


B
Go to step 7

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


6. CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Replace the navigation receiver assembly with a normally functioning one (Click here).

  1. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

    OK:
    Malfunction does not reoccur (returns to normal).

Result 
Proceed to
Result
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A

END (NAVIGATION RECEIVER ASSEMBLY IS DEFECTIVE)

7. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Replace the radio and display receiver assembly with a normally functioning one (Click here).

  1. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

    OK:
    Malfunction does not reoccur (returns to normal).

Result 
Proceed to
Result
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A

END (RADIO AND DISPLAY RECEIVER ASSEMBLY IS DEFECTIVE)


← U0073 Control Module Communication Bus OFF (+ 5 more codes) (from Aug 2014)Image from Camera for Parking Assist Monitor is Abnormal (from Aug 2014) →