C1683 Side Camera Feedback Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C1684 Side Camera Current Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1683 |
Side Camera Feedback Malfunction |
|
| C1684 |
Side Camera Current Malfunction |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1683 and C1684 are not output
A
DTC C1683 and/or C1684 is output
B
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY) |
Disconnect the I7 parking assist ECU connector.
Disconnect the J3*1 or K2*2 front passenger side outer rear view mirror assembly connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
I7-34 (SCV-) - J3-12 (SCV-)
Always
Below 1 Ω
I7-10 (SCV+) - J3-6 (SCV+)
Always
Below 1 Ω
I7-33 (SGND) - J3-13 (SGND)
Always
Below 1 Ω
I7-32 (SCB+) - J3-5 (SCB+)
Always
Below 1 Ω
I7-34 (SCV-) - Body ground
Always
10 kΩ or higher
I7-10 (SCV+) - Body ground
Always
10 kΩ or higher
I7-33 (SGND) - Body ground
Always
10 kΩ or higher
I7-32 (SCB+) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
I7-34 (SCV-) - K2-12 (SCV-)
Always
Below 1 Ω
I7-10 (SCV+) - K2-6 (SCV+)
Always
Below 1 Ω
I7-33 (SGND) - K2-13 (SGND)
Always
Below 1 Ω
I7-32 (SCB+) - K2-5 (SCB+)
Always
Below 1 Ω
I7-34 (SCV-) - Body ground
Always
10 kΩ or higher
I7-10 (SCV+) - Body ground
Always
10 kΩ or higher
I7-33 (SGND) - Body ground
Always
10 kΩ or higher
I7-32 (SCB+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK PARKING ASSIST ECU |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
I7-33 (SGND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I7-32 (SCB+) - I7-33 (SGND)
Engine switch on (IG), wide view front and side monitor switch on
5.5 to 7.05 V
| *a |
Component with harness connected (Parking Assist ECU) |
| Result |
Proceed to |
| OK |
A |
| NG (for LHD) |
B |
| NG (for RHD) |
C |
|
|
||||
|
|
||||
| A | |
| 4. CHECK FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY |
Measure the waveform of the front passenger side television camera assembly using an oscilloscope.


Text in Illustration *a
Component with harness connected
(Parking Assist ECU)
*b
Waveform A
*c
Waveform B
*d
Synchronized Signal
*e
Video Waveform
-
-
- HINT:
- A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
- *1: for Navigation Receiver Type
- *2: for Radio and Display Type
- The video waveform changes according to the image sent by the side television camera assembly.
- A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
Measurement Condition Item
Content
Tester Connection
I7-10 (SCV+) - I7-33 (SGND)
Tool Setting
200 mV/DIV., 50 μsec./DIV.
Condition
- Waveform A: Engine switch on (IG), wide view front and side monitor switch on, camera lens not covered, displaying image
- Waveform B: Engine switch on (IG), wide view front and side monitor switch on, camera lens covered, blacking out screen
- OK:
- Waveform is as shown in illustration.
| Result |
Proceed to |
| OK (for LHD) |
A |
| OK (for RHD) |
B |
| NG |
C |
|
|
||||
|
|
||||
| A | ||
| ||
| 5. REPLACE FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY |
Replace the front passenger side television camera assembly with a new or normally functioning one (Click here).
| NEXT | |
| 6. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1683 and C1684 are not output
A
DTC C1683 and/or C1684 is output
B
|
|
||||
| A | ||
| ||
