2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

C1683 Side Camera Feedback Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.
DTC Code
DTC Detection Condition
Trouble Area
C1683
Side Camera Feedback Malfunction
  1. Harness or connector
  2. Parking assist ECU
  3. Front passenger side television camera assembly
  4. Front passenger side outer rear view mirror assembly
C1684
Side Camera Current Malfunction
  1. Harness or connector
  2. Parking assist ECU
  3. Front passenger side television camera assembly
  4. Front passenger side outer rear view mirror assembly

WIRING DIAGRAM

E283780E03

INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1683 and C1684 are not output
    A
    DTC C1683 and/or C1684 is output
    B



B
Go to step 2
A

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY)
  1. Disconnect the I7 parking assist ECU connector.

  1. Disconnect the J3*1 or K2*2 front passenger side outer rear view mirror assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I7-34 (SCV-) - J3-12 (SCV-)
    Always
    Below 1 Ω
    I7-10 (SCV+) - J3-6 (SCV+)
    Always
    Below 1 Ω
    I7-33 (SGND) - J3-13 (SGND)
    Always
    Below 1 Ω
    I7-32 (SCB+) - J3-5 (SCB+)
    Always
    Below 1 Ω
    I7-34 (SCV-) - Body ground
    Always
    10 kΩ or higher
    I7-10 (SCV+) - Body ground
    Always
    10 kΩ or higher
    I7-33 (SGND) - Body ground
    Always
    10 kΩ or higher
    I7-32 (SCB+) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I7-34 (SCV-) - K2-12 (SCV-)
    Always
    Below 1 Ω
    I7-10 (SCV+) - K2-6 (SCV+)
    Always
    Below 1 Ω
    I7-33 (SGND) - K2-13 (SGND)
    Always
    Below 1 Ω
    I7-32 (SCB+) - K2-5 (SCB+)
    Always
    Below 1 Ω
    I7-34 (SCV-) - Body ground
    Always
    10 kΩ or higher
    I7-10 (SCV+) - Body ground
    Always
    10 kΩ or higher
    I7-33 (SGND) - Body ground
    Always
    10 kΩ or higher
    I7-32 (SCB+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK PARKING ASSIST ECU

  1. E245958E31
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-33 (SGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I7-32 (SCB+) - I7-33 (SGND)
    Engine switch on (IG), wide view front and side monitor switch on
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)
Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A


4. CHECK FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY

  1. Measure the waveform of the front passenger side television camera assembly using an oscilloscope.E245725E30

    Text in Illustration 
    *a
    Component with harness connected
    (Parking Assist ECU)
    *b
    Waveform A
    *c
    Waveform B
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    HINT:
    1. A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
      1. *1: for Navigation Receiver Type
      2. *2: for Radio and Display Type
    2. The video waveform changes according to the image sent by the side television camera assembly.

    Measurement Condition 
    Item
    Content
    Tester Connection
    I7-10 (SCV+) - I7-33 (SGND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    1. Waveform A: Engine switch on (IG), wide view front and side monitor switch on, camera lens not covered, displaying image
    2. Waveform B: Engine switch on (IG), wide view front and side monitor switch on, camera lens covered, blacking out screen

    OK:
    Waveform is as shown in illustration.

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
Go to step 5
A

REPLACE PARKING ASSIST ECU (Click here)

5. REPLACE FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY
  1. Replace the front passenger side television camera assembly with a new or normally functioning one (Click here).


NEXT


6. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1683 and C1684 are not output
    A
    DTC C1683 and/or C1684 is output
    B



B
REPLACE FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY (Click here)
A

END (FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)C1683 Side Camera Feedback Malfunction (+ C1684) (from Aug 2014) →