2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

U0235 Lost Communication with Cruise Control Front Distance Range Sensor

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU transit the data for the general vehicle control diagnosis function along the communication line. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU.
DTC Code
DTC Detection Condition
Trouble Are
U0235
When the ignition switch is ON, a communication error between the millimeter wave radar sensor assembly and driving support ECU is detected for 1 second.
  1. Harness or connector
  2. Millimeter wave radar sensor assembly
  3. Driving support ECU

WIRING DIAGRAM

E192826E03

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC being output.


1. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BATTERY AND BODY GROUND)

  1. E178436E04
    Disconnect the G119 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    G119-30 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G119-25 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Driving Support ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BODY GROUND)

  1. E178319E05
    Disconnect the A15 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-2 (SGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR)
  1. Disconnect the G119 ECU connector.

  1. Disconnect the A15 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G119-16 (LRDD) - A15-3 (LRDD)
    Always
    Below 1 Ω
    G119-16 (LRDD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK DRIVING SUPPORT ECU

  1. E192827E03
    Disconnect the A15 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G119-16 (LRDD) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component without harness connected
    (Driving Support ECU)



NG
REPLACE DRIVING SUPPORT ECU (Click here)
OK


5. REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
  1. Replace the millimeter wave radar sensor assembly (Click here).


NEXT


6. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
  1. Adjust the millimeter wave radar sensor assembly (Click here).


NEXT


7. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC U0235 is not output.



NG
REPLACE DRIVING SUPPORT ECU (Click here)
OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY IS DEFECTIVE)


← U0122 Lost Communication with Vehicle Dynamics Control Module (+ 5 more codes) (from Aug 2014)U0235 Lost Communication with Cruise Control Front Distance Range Sensor (from Aug 2014) →