U0235 Lost Communication with Cruise Control Front Distance Range Sensor
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The millimeter wave radar sensor assembly and driving support ECU transit the data for the general vehicle control diagnosis function along the communication line. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU.| DTC Code |
DTC Detection Condition |
Trouble Are |
| U0235 |
When the ignition switch is ON, a communication error between the millimeter wave radar sensor assembly and driving support ECU is detected for 1 second. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC being output.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BATTERY AND BODY GROUND) |
Disconnect the G119 ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage :
Tester Connection
Switch Condition
Specified Condition
G119-30 (B) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G119-25 (GND) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Driving Support ECU) |
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BODY GROUND) |
Disconnect the A15 sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A15-2 (SGND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR) |
Disconnect the G119 ECU connector.
Disconnect the A15 sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G119-16 (LRDD) - A15-3 (LRDD)
Always
Below 1 Ω
G119-16 (LRDD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK DRIVING SUPPORT ECU |
Disconnect the A15 sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G119-16 (LRDD) - Body ground
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Component without harness connected
(Driving Support ECU)
|
|
||||
| OK | |
| 5. REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
Replace the millimeter wave radar sensor assembly (Click here).
| NEXT | |
| 6. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
Adjust the millimeter wave radar sensor assembly (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC U0235 is not output.
|
|
||||
| OK | ||
| ||
