U1104 Lost Communication with Driving Support ECU
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
| DTC Code |
DTC Detection Condition |
Trouble Are |
| U1104 |
When the ignition switch is ON, a communication error between the millimeter wave radar sensor assembly and driving support ECU is detected for 1 second. |
|
| U1104 |
When the ignition switch is ON, communication stops between the seat belt control ECU and driving support ECU for 1 second or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC being output.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (Click here).
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC U1104 is not output
A
DTC U1104 is output from driving support ECU (Pre-Crash 2)
B
DTC U1104 is output from seat belt control ECU (Pre-Crash)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BATTERY AND BODY GROUND) |
Disconnect the A15 sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage :
Tester Connection
Switch Condition
Specified Condition
A15-5 (IGB) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A15-2 (SGND) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly) |
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BODY GROUND) |
Disconnect the G119 ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G119-25 (GND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Driving Support ECU)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU) |
Disconnect the A15 sensor connector.
Disconnect the G119 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A15-4 (LRRD) - G119-38 (LRRD)
Always
Below 1 Ω
A15-4 (LRRD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. REPLACE DRIVING SUPPORT ECU |
Replace the driving support ECU (Click here).
| NEXT | |
| 6. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC U1104 is not output.
|
|
||||
| OK | ||
| ||
| 7. CHECK CAN COMMUNICATION SYSTEM |
Select "Bus Check" from the "System Select" screen on the intelligent tester.
Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".
Result Result
Proceed to
CAN DTC is not output
A
CAN DTC is output (for LHD with Entry and Start System)
B
CAN DTC is output (for LHD without Entry and Start System)
C
CAN DTC is output (for RHD with Entry and Start System)
D
CAN DTC is output (for RHD without Entry and Start System)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
