2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

U1104 Lost Communication with Driving Support ECU

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Are
U1104
When the ignition switch is ON, a communication error between the millimeter wave radar sensor assembly and driving support ECU is detected for 1 second.
  1. Harness or connector
  2. Millimeter wave radar sensor assembly
  3. Driving support ECU
U1104
When the ignition switch is ON, communication stops between the seat belt control ECU and driving support ECU for 1 second or more.
  1. Seat belt control ECU
  2. CAN communication system
  3. Driving support ECU

WIRING DIAGRAM

E200099E02

INSPECTION PROCEDURE

NOTICE:
  1. When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC being output.


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC U1104 is not output
    A
    DTC U1104 is output from driving support ECU (Pre-Crash 2)
    B
    DTC U1104 is output from seat belt control ECU (Pre-Crash)
    C



B
Go to step 2

C
Go to step 7
A

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BATTERY AND BODY GROUND)

  1. E178319E06
    Disconnect the A15 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    A15-5 (IGB) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-2 (SGND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BODY GROUND)

  1. E178436E05
    Disconnect the G119 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G119-25 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU)
  1. Disconnect the A15 sensor connector.

  1. Disconnect the G119 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-4 (LRRD) - G119-38 (LRRD)
    Always
    Below 1 Ω
    A15-4 (LRRD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE DRIVING SUPPORT ECU
  1. Replace the driving support ECU (Click here).


NEXT


6. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC U1104 is not output.



NG
REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (Click here)
OK

END (DRIVING SUPPORT ECU IS DEFECTIVE)

7. CHECK CAN COMMUNICATION SYSTEM
  1. Select "Bus Check" from the "System Select" screen on the intelligent tester.

  1. Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD with Entry and Start System)
    B
    CAN DTC is output (for LHD without Entry and Start System)
    C
    CAN DTC is output (for RHD with Entry and Start System)
    D
    CAN DTC is output (for RHD without Entry and Start System)
    E



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← U1104 Lost Communication with Driving Support ECU (Aug 2013 – Jul 2014)Pre-crash Safety Brake Cancel Switch Circuit (Aug 2013 – Jul 2014) →